Intel SE7320VP2 User Guide - Page 40

Problems following Initial System Installation, First Steps Checklist - driver

Get Intel SE7320VP2 PDF manuals and user guides View all Intel SE7320VP2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

Troubleshooting Problems following Initial System Installation Problems that occur at initial system startup are usually caused by an incorrect installation or configuration. Hardware failure is a less frequent cause. If the problem you are experiencing is with a specific software application, see "Problems with Newly Installed Application Software." First Steps Checklist ‰ Is AC power available at the wall outlet? ‰ Are the power supplies plugged in? Check the AC cable(s) on the back of the chassis and at the AC source. ‰ Are all cables correctly connected and secured? ‰ Are the processors fully seated in their sockets on the server board? ‰ Are all standoffs in the proper location and not touching any components, causing a potential short? ‰ Are all add-in PCI boards fully seated in their slots on the server board? ‰ Are all jumper settings on the server board correct? ‰ Are all jumper and switch settings on add-in boards and peripheral devices correct? To check these settings, refer to the manufacturer's documentation that comes with them. If applicable, ensure that there are no conflicts-for example, two add-in boards sharing the same interrupt. ‰ Are all peripheral devices installed correctly? ‰ If the system has a hard disk drive, is it properly formatted or configured? ‰ Are all device drivers properly installed? ‰ Are the configuration settings made in Setup correct? ‰ Is the operating system properly loaded? Refer to the operating system documentation. ‰ Did you press the system power on/off switch on the front panel to turn the server on (power on light should be lit)? ‰ Is the system power cord properly connected to the system and plugged into a NEMA 5-15R outlet for 100-120 V or a NEMA 6-15R outlet for 200-240 V ? ‰ Are all integrated components from the tested components lists? Check the tested memory, and chassis lists, as well as the supported hardware and operating system list. See "Additional Information and Software" for links to the tested component lists. 40

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
Troubleshooting
Problems following Initial System Installation
Problems that occur at initial system startup are usually caused by an incorrect installation or
configuration.
Hardware failure is a less frequent cause.
If the problem you are experiencing is
with a specific software application, see “
Problems with Newly Installed
Application Software
.
”
First Steps Checklist
Is AC power available at the wall outlet?
Are the power supplies plugged in?
Check the AC cable(s) on the back of the chassis and at the
AC source.
Are all cables correctly connected and secured?
Are the processors fully seated in their sockets on the server board?
Are all standoffs in the proper location and not touching any components, causing a potential
short?
Are all add-in PCI boards fully seated in their slots on the server board?
Are all jumper settings on the server board correct?
Are all jumper and switch settings on add-in boards and peripheral devices correct?
To check
these settings, refer to the manufacturer’s documentation that comes with them.
If applicable,
ensure that there are no conflicts—for example, two add-in boards sharing the same interrupt.
Are all peripheral devices installed correctly?
If the system has a hard disk drive, is it properly formatted or configured?
Are all device drivers properly installed?
Are the configuration settings made in Setup correct?
Is the operating system properly loaded?
Refer to the operating system documentation.
Did you press the system power on/off switch on the front panel to turn the server on (power on
light should be lit)?
Is the system power cord properly connected to the system and plugged into a
NEMA 5-15R outlet for 100-120 V
or a NEMA 6-15R outlet for 200-240 V
?
Are all integrated components from the tested components lists? Check the tested memory, and
chassis lists, as well as the supported hardware and operating system list. See “
Additional
Information and Software
” for links to the tested component lists.
40