Intel SR2520SAXR User Guide - Page 59

Installing and Removing a Hot-swap Hard Drive, SR2520SAX/SR2520SAXS and SR2520SAXR, SR2520SAXSR

Get Intel SR2520SAXR - Server System - 0 MB RAM PDF manuals and user guides
UPC - 735858197335
View all Intel SR2520SAXR manuals
Add to My Manuals
Save this manual to your list of manuals

Page 59 highlights

9. Raise the CPU load plate. 10. Remove the processor. 11. If installing a replacement processor, see "Installing the Processor". Otherwise, install the protective socket cover over the empty processor socket and reinstall the system's cover. Installing and Removing a Hot-swap Hard Drive (SR2520SAX/SR2520SAXS and SR2520SAXR/ SR2520SAXSR) Up to six hot-swap SATA drives or SAS drives can be installed. Cautions: If you install less than six drives or devices, the empty drive bays must be occupied by carriers with baffles to maintain proper system cooling. To avoid possible damage to your server system, do not use older style drive carriers. Note: The server system does not support all hard drives. See "Server System References" for an Internet link to a list of supported hardware. Installing a SAS or SATA Hot-swap Hard Disk Drive (SR2520SAX/SR2520SAXS and SR2520SAXR/ SR2520SAXSR) 1. Remove the front bezel if it is installed. For instructions, see "Removing the Front Bezel". 2. Open the green latch at the front of the hard drive carrier. 3. Pull out on the black lever and slide the carrier from the server system. Intel® Server System SR2520SA User's Guide 37

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
Intel
®
Server System SR2520SA User’s Guide
37
9.
Raise the CPU load plate.
10.
Remove the processor.
11.
If installing a replacement processor, see
“Installing the Processor”
. Otherwise,
install the protective socket cover over the empty processor socket and reinstall the
system’s cover.
Installing and Removing a Hot-swap Hard Drive
(SR2520SAX/SR2520SAXS and SR2520SAXR/
SR2520SAXSR)
Up to six hot-swap SATA drives or SAS drives can be installed.
Cautions:
If you install less than six drives or devices, the empty drive bays must be occupied by
carriers with baffles to maintain proper system cooling.
To avoid possible damage to your server system, do not use older style drive carriers.
Note:
The server system does not support all hard drives. See
“Server System References“
for
an Internet link to a list of supported hardware.
Installing a SAS or SATA Hot-swap Hard Disk Drive
(SR2520SAX/SR2520SAXS and SR2520SAXR/
SR2520SAXSR)
1.
Remove the front bezel if it is installed. For instructions, see
“Removing the Front
Bezel”
.
2.
Open the green latch at the front of the hard drive carrier.
3.
Pull out on the black lever and slide the carrier from the server system.