JVC DT-V1900CGU Instruction Manual - Page 16
Function Setting, Picture Sub Adj.
View all JVC DT-V1900CGU manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 16 highlights
HOW TO USE "SETUP MENU" (cont'd) Ⅵ ITEM CONTENTS AND ADJUSTMENT RANGE/SETTINGS 1. FUNCTION SETTING Selects the color system and displays the monitor's powerup time or the total usage time. Press the button to display the setting menu illustrated on the right. COLOR SYSTEM SYNC SELECT RUSH DELAY TIME TALLY SELECT REMOTE SYSTEM EMBEDDED HOUR METER X100h :AUTO :INT. :STD. :GREEN :MAKE :1G :000 EXIT: MENU ADJUST:- + SELECT: Item : COLOR SYSTEM Settings : AUTO/NTSC/PAL Function : Selects the color system when using the video input card. AUTO : Change NTSC and PAL automatically. NTSC : Keeps the color system NTSC. PAL : Keeps the color system PAL. NOTE : Normally select AUTO. However, if the input signal is unstable, select NTSC or PAL. Item : SYNC SELECT Settings : INT./EXT. Function : Synchronized signal selection. INT. : The input video signal is synchronized with the built-in sync signal. EXT. : The input video signal is synchronized with an external signal from an external sync terminal. * The external synchronized signal terminals apply to the HD/ CS terminal and VD terminal (in the RGB/COMPONENT Input Card), or the EXT. SYNC terminal (in the VIDEO Input Card). * This item is not shown when only SDI and/or HD SD input cards are installed. Item : RUSH DELAY TIME Settings : STD./SLOW Function : Sets the time when the power supply to the monitor's circuits (excluding the micro computers) starts after the power switch is pressed. STD. : The power supply starts approx. 1 second after the power switch is pressed. SLOW : The power supply starts approx. 3.2 seconds after the power switch is pressed. NOTE : If you are going to turn several Multi-Format Monitors on at the same time, it is recommended to apply SLOW to some of the monitors to control rush current. Item : TALLY SELECT Settings : GREEN/RED Function : Selects the color of the tally lamp (when lit) on the upper front panel. GREEN: The tally lamp lights in green. RED : The tally lamp lights in red. NOTE : Set the MAKE/TRIGGER terminal's tally control in the REMOTE (external control) terminal setup menu. For details, refer to Page 20. To set the color, use TALLY SELECT in the "FUNCTION SETTING" setup menu or MAKE/TRIGGER in the REMOTE (external control) terminal setup menu. For details, refer to Page 16 and 20. Item Settings Function : REMOTE SYSTEM : MAKE/TRIGGER : Selects the contact system (MAKE (make contact) or TRG. (trigger contact)) for the MAKE/ TRIGGER terminals. MAKE (make contact system): Controls the function by stable disconnection (terminal open) or short-circuit (short with GND of 15th terminal) of the controlled terminal. TRG. (trigger system): Controls the function by instantaneously (one second) short-circuiting (short with GND of 15th terminal) the controlled terminal. Item Settings : EMBEDDED : 1G/2G/1-2G 1G : 1ch 2ch 3ch 4ch 1-2ch 3-4ch 1-4ch 2G : 5ch 6ch 7ch 8ch 5-6ch 7-8ch 5-8ch 1-2G : 1ch 2ch 3ch 4ch 5ch 6ch 7ch 8ch 1-2ch AUTO 5-8ch 1-4ch 7-8ch 5-6ch 3-4ch Function : Selects Embedded Audio signal channels. NOTE: The auto setting mixes and outputs all 8 signal channels. Output level is automatically detected and set at FPGA according to the channel numbers that are receiving signals. * About sound output level Sound output level is set to a standard output level for all channels when several sound channels are output at the same time. The more channels are selected, the lower each channel's level will be. (Each channel's level becomes half for 1- 2 channel, 1/4 for 1- 4 channel.) *About AUTO When AUTO is selected, the number of sound channels in use is detected. The level of each channel is automatically adjusted to ensure that the total sound output level is equiva- lent to the standard output level. * This item is shown when an input card compliant with EMBEDDED AUDIO is installed. Item Number range Function : HOUR METER X100h : 000 ~ 655 : Displays the total usage time of the monitor in hundred-hour units. ● When the timer passes 655, it returns to 000. ● The timer does not count the usage time under one hour. 2. PICTURE SUB ADJ. Performs approximate adjustments using the control knobs on the front panel. Press the button to display the setting menu illustrated on the right. CONTRAST BRIGHT CHROMA PHASE NTSC SETUP COMPO.LEVEL sub menu reset : 00 : 00 : 00 : 00 : 00 :SMPTE NOTE : When the RGB signal EXIT: MENU ADJUST:- + SELECT: is input, only CONTRAST and BRIGHT are displayed. When the PAL signal is input, only CONTRAST, BRIGHT and CHROMA are displayed. 16 LCT1117-001C 16 02.6.6, 11:38 AM