JVC DT-V1900CGU Instruction Manual - Page 20
How To Use External, Control
View all JVC DT-V1900CGU manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 20 highlights
HOW TO USE EXTERNAL CONTROL Ⅵ ABOUT EXTERNAL CONTROL The Multi-Format Monitor has two external control terminals. One is the MAKE/TRIGGER terminal, which allows the monitor to be controlled by the MAKE(make contact) or TRG. (trigger contact) method selected in the function setting. MAKE (make contact system): Controls the function by stable disconnection (terminal open) or short-circuiting (short with GND of 15th terminal) of the controlled terminal. TRG. (trigger system) : Controls the function by instantaneously (one second) short-circuiting (short with GND of 15th terminal) the controlled terminal. * MAKE or TRIGGER are selected from REMOTE SELECT in the setup menu. * The 14th terminal (REMOTE ENABLE) is always controlled by the make contact system regardless of the REMOTE SELECT setting. The other terminal used for remote control is the RS-232C terminal. This allows the monitor to be controlled by a PC via serial communication. NOTE: Control priority is in the following order; 1 MAKE/TRIGGER terminal > 2 RS-232C terminal > 3 front panel buttons. When trigger contact is on, the front panel buttons can be operated. Ⅵ HOW TO USE THE MAKE/TRIGGER TERMINAL Connections Connect (short-circuit) the 15th terminal (GND) to each of the 1st through 14th terminals in the 3-line 15-pin D-sub connector. The functions of each terminal are listed below. The Names and Functions of Terminals 10 9 8 54321 76 15 14 13 12 11 No. Names Functions Operations (OFF p[ ON) *1 1 TALLY Puts on the tally lamp. Put off Put on 2 INPUT A Changes the input to INPUT A Not change Change 3 INPUT B Changes the input to INPUT B Not change Change 4 INPUT C Changes the input to INPUT C Not change Change 5 INPUT D Changes the input to INPUT D Not change Change 6 INPUT E Changes the input to INPUT E Not change Change 7 INPUT F Changes the input to INPUT F Not change Change 8 COLOR OFF Changes the picture black-and-white. Not change Change 9 AREA MARKER Displays the area marker. Not display Display 10 ASPECT Changes the screen ratio to 16:9 4:3 16:9 11 TALLY SELECT Switch the tally lamp color. GREEN RED 12 MARKER Selects the type of the area marker Selection in the main unit Selection in the remote *2 control 13 STATUS Displays the monitor's status Display *3 14 REMOTE ENABLE Makes the external control form the Invalid Valid *4 MAKE terminal valid or invalid 15 GND Used as a ground terminal - - *1 : OFF stands for disconnection, and ON stands for short-circuit. When trigger contact is on, the setting switches between ON and OFF every time the terminal is short-circuited. (Only TALLY is controlled by being OFF(disconnection) and ON(short-circuit).) *2 : Selects the area marker size from AREA MARKER (setting on the main unit) or AREA MARKER-R (setting on the remote control) setting. *3 : The STATUS function is activated when the connection to the STATUS terminal is changed (ON to OFF, or OFF to ON). The monitor's status is displayed for 3 seconds. *4 : Setting REMOTE ENABLE to ON enables remote control. (same for both MAKE/TRIGGER methods.) Operation 1. Set REMOTE ENABLE to ON. 2. Short-circuit or disconnect the desired terminal. (When trigger contact is on, duration of short-circuit is approx. 1 second.) Changing the Signal Input 1. Set REMOTE ENABLE to ON. 2. Short-circuit the desired INPUT terminal. (When trigger contact is on, duration of short-circuit is approx. 1 second.) 3. Disconnect the INPUT terminal selected above. The signal input is actually changed after the disconnection has been completed. NOTES: • When more than two terminals are selected (short-circuited) from INPUT A through INPUT F, the signal input is not changed. To control INPUT A through INPUT F, we recommend using the interlock switch, which turns off a switch when another switch is turned on. • When trigger contact is on, and if several terminals are short-circuited simultaneously, proper control cannot be done. It is always necessary to short-circuit one terminal for one operation. Also, use of the Tact Switch is recommended. 20 LCT1117-001C 20 02.6.6, 11:39 AM