JVC KY-F70BU Instruction Manual - Page 16

Pin configurations of connectors

Get JVC KY-F70BU - Sxga Imaging Camera Less Lens PDF manuals and user guides View all JVC KY-F70BU manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

1. Introduction (continued) Pin configurations of connectors Power terminal (Mini DIN 8-pin, female) 7 8 6 Pin no. 1 2 3 4 5 6 7 8 5 3 2 4 1 NC GND NC NC GND 12V NC 12V Signal name Lens terminal (Metal 12-pin, female) 10 9 1 8 2 7 3 6 4 12 5 11 Pin no. 1 2 3 4 5 6 7 8 9 to 12 Signal name NC FREEZE GND NC IRIS CONTROL 12V DC IRIS POSITION IRIS AUTO /MANU NC Remote terminal (Metal 10-pin, female) 8 1 7 2 10 9 Pin no. 1 2 3 4 5 6 7 8 9 10 6 5 3 4 Signal name A. WHITE L active Zi=22k Ω FREEZE L active Zi=100k Ω WEN L active Zo=22 Ω 3.3V(p-p) FLASH SEND RS-SDI RS-SDO GND 12V OPERATION CAUTION • Consult your JVC dealer concerning the remote terminal connection. • Remote cable must use shielded cable. Outer shield of remote cable must to connect 10-pin connector outer metal shell. Terminal name I/O Conditions FREEZE WEN IN • 5V CMOS • Schmidt Trigger • Pull-up to 5V at 100k Ω OUT • 3.3V (p-p) negative polarity • Contact point recommended • Maximum rated voltage: 5.3V • H level: 3.5 ~ 5.0V • L level: 0 ~ 0.8V • CMOS (5V): OK* • TLL not possible • Pulse width: 130 µs or higher • Output only when in the SXGA mode FLASH OUT • Open collector • Maximum rated current: 150mA • Maximum rated voltage: 12V * However, insert a diode as shown in the diagram below. KY-F70B E12 C Mos IC

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
E12
1
4
3
6
7
8
5
2
1. Introduction (continued)
Power terminal (Mini DIN 8-pin, female)
Pin configurations of connectors
Pin no.
Signal name
1
NC
2
GND
3
NC
4
NC
5
GND
6
12V
7
NC
8
12V
Lens terminal (Metal 12-pin, female)
Pin no.
Signal name
1
NC
2
FREEZE
3
GND
4
NC
5
IRIS CONTROL
6
12V DC
7
IRIS POSITION
8
IRIS AUTO /MANU
9 to 12
NC
6
7
8
2
1
9
3
4
12
5
10
11
Terminal
name
FREEZE
WEN
FLASH
Remote terminal (Metal 10-pin, female)
Pin no.
Signal name
1
A. WHITE L active Zi=22k
Ω
2
FREEZE L active Zi=100k
Ω
3
WEN L active Zo=22
Ω
3.3V(p-p)
4
FLASH
5
SEND
6
RS-SDI
7
RS-SDO
8
GND
9
12V
10
OPERATION
1
2
8
7
10
6
3
4
5
9
CAUTION
•
Consult your JVC dealer concerning the re-
mote terminal connection.
•
Remote cable must use shielded cable.
Outer shield of remote cable must to connect
10-pin connector outer metal shell.
*
However, insert a diode as shown in the dia-
gram below.
I/O
IN
•
5V CMOS
•
Schmidt Trigger
•
Pull-up to 5V at
100k
Ω
OUT
•
3.3V (p-p)
negative polarity
OUT
•
Open collector
Conditions
•
Contact point
recommended
•
Maximum rated
voltage: 5.3V
•
H level: 3.5 ~ 5.0V
•
L level: 0 ~ 0.8V
•
CMOS (5V): OK*
•
TLL not possible
•
Pulse width:
130
µ
s or higher
•
Output only when
in the SXGA mode
•
Maximum rated
current: 150mA
•
Maximum rated
voltage: 12V
KY-F70B
C Mos IC