JVC KY-F70BU Instruction Manual - Page 23

Connecting a monitor

Get JVC KY-F70BU - Sxga Imaging Camera Less Lens PDF manuals and user guides View all JVC KY-F70BU manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

Connecting a monitor Connect the PC monitor (VGA) to the MONITOR terminal on the rear of the main unit. SCSI REC SEND AW/SEL MODE MENU UP DOWN SET PLAY FREEZE MONITOR LENS REMOTE ON 1 2 3 4 DC IN POWER SEE INSTRUCTION MANUAL MONITOR terminal CAUTION • Before connecting, make sure that the power of all systems are turned off. Connecting with the power turned on may result in malfunction. MEMO • The monitor cable must use clump filter for both ends to minimize emission of unwanted electrical waves. (Commercially available VGA video cable is recommended) • For the pin assignment, see page 13 Pin configuration of connectors • Monitor conditions: fH: 31.47 kHz fV: 59.94 Hz Sync signal: H/V separate, TTL negative polarity • Dip switch setting ( ੬ page 24) VGA mode (set dip switch No. 3 to OFF) Do not connect the unit to a VGA monitor directly when in the SXGA mode (dip switch No. 3 ON) E19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
E19
Connecting a monitor
Connect the PC monitor (VGA) to the MONITOR terminal on the rear of the main unit.
SEE INSTRUCTION MANUAL
POWER
DC IN
REMOTE
MONITOR
LENS
FREEZE
PLAY
SET
DOWN
AW/SEL
SEND
SCSI
UP
MENU
MODE
REC
ON 1
234
MONITOR terminal
MEMO
•
The monitor cable must use clump filter for both ends to minimize emission of unwanted electrical
waves. (Commercially available VGA video cable is recommended)
•
For the pin assignment, see page 13 Pin configuration of connectors
•
Monitor conditions:
fH: 31.47 kHz
fV: 59.94 Hz
Sync signal: H/V separate, TTL negative polarity
•
Dip switch setting
(
±
page 24)
VGA mode (set dip switch No. 3 to OFF)
Do not connect the unit to a VGA monitor directly when in the SXGA mode (dip switch No. 3 ON)
CAUTION
•
Before connecting, make sure that the power of all systems are turned off. Connecting with the power
turned on may result in malfunction.