JVC VN-C3U VN-C3U Vnetworks camera Instruction Manual (1511KB) - Page 9

VN-C3U Installation and Setup

Get JVC VN-C3U - V-networks Pan/tilt/zoom Camera PDF manuals and user guides View all JVC VN-C3U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

VN-C3U Installation and Setup Before starting installation and setup It is necessary to set an IP address for each VN-C3U unit. Use the following procedure for the setup of each unit. (If the power is not turned on, the installation of multiple VN-C3U can be performed at one time.) 1. Install the VN-C3U h In case of installation in a location where the power cannot easily be turned on, complete steps 2 - 5 before step 1. 2. Connect the VN-C3U to the network and turn the power on. 3. Set the VN-C3U IP address. h When setting the VN-C3U IP address, be sure to contact the network administrator for assignment or approval. When installing the second and following units, reboot the PC and then return to step 2. 4. Enable the VN-C3U IP address. (Turn the VN-C3U power off and then on again.) 5. Register the connection point. h This registers the VN-C3U IP address data in the PC. Names of VN-C3U parts Rear view Side view Lens unit Front view Lens cover DC IN jack 10BASE-T port Body Alarm IN/OUT jack %$7 #"4&5  7.$6@&+ 10 00.4.7, 5:34 PM

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
10
VN-C3U Installation and Setup
Before starting installation and setup
It is necessary to set an IP address for each VN-C3U unit. Use the following
procedure for the setup of each unit. (If the power is not turned on, the
installation of multiple VN-C3U can be performed at one time.)
1.
Install the VN-C3U
In case of installation in a location where the power cannot easily be
turned on, complete steps 2 - 5 before step 1.
2.
Connect the VN-C3U to the network and turn the power on.
3.
Set the VN-C3U IP address.
When setting the VN-C3U IP address, be sure to contact the network
administrator for assignment or approval. When installing the second
and following units, reboot the PC and then return to step 2.
4.
Enable the VN-C3U IP address.
(Turn the VN-C3U power off and then on again.)
5.
Register the connection point.
This registers the VN-C3U IP address data in the PC.
Names of VN-C3U parts
10BASE-T
10BASE-T
DC12V
DC12V
Rear view
DC IN jack
10BASE-T port
Body
Alarm IN/OUT jack
Side view
Front view
Lens cover
Lens unit
VM-C3U_E.65J
00.4.7, 5:34 PM
10