Jabra JX10 User Manual - Page 17

For use with desk phone with GN 1000 remote handset lifter - user manual

Get Jabra JX10 - w Bluetooth Hub PDF manuals and user guides
UPC - 706487008651
View all Jabra JX10 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

English 4c For use with desk phone with GN 1000 (remote handset lifter) The GN 1000 lifts or lowers your handset automatically, allowing you to answer and end calls when you're away from your desk. Jabra Bluetooth Hub setup Connecting your Jabra Bluetooth Hub with desk phone and power supply • Disconnect the handset from your desk phone (by unplugging the handset from the socket on the desk phone). • Connect the handset to your Bluetooth Hub's handset socket . • Connect the desk phone handset socket to the Bluetooth Hub desk phone socket  using the supplied connection cord (desk phone-to-Bluetooth Hub ). • Connect the GN 1000 to the AUX socket  on the Bluetooth Hub (see GN 1000 User Manual). • Connect the power supply to your Bluetooth Hub's power supply socket . • Connect the power supply to the wall power socket. • You can use the 'wire guide' at the bottom of the Bluetooth Hub to neatly guide the cable from the desk phone to the wall phone plug. The green LED indicates that the Bluetooth Hub power is on. Please refer to the GN 1000 User Manual for directions on how to set up your GN 1000. When the LED is green and the GN 1000 is installed, please move on to "Adjust setting with a test call from your desk phone" instructions. In the unlikely event that the Bluetooth Hub is not OK, its LED will flash red. • First, try disconnecting and reconnecting the Bluetooth Hub from the power source. • If the LED is still flashing red, you must reset your Bluetooth Hub. o Press and hold the Bluetooth Hub reset button . o The reset light will turn solid red for 3 seconds, and then turn green. • If the LED is still flashing red, after disconnect and reset, please contact your dealer. IMPORTANT: Following reset, you must pair your Bluetooth Hub and headset. 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
4c
For use with desk phone with GN 1000 (remote handset lifter)
The GN 1000 lifts or lowers your handset automatically, allowing you to answer and end
calls when you’re away from your desk.
Jabra Bluetooth Hub setup
Connecting your Jabra Bluetooth Hub with desk phone and power supply
•
Disconnect the handset from your desk phone (by unplugging the handset from the
socket on the desk phone).
•
Connect the handset to your Bluetooth Hub’s handset socket
.
•
Connect the desk phone handset socket to the Bluetooth Hub desk phone socket
using the supplied connection cord (desk phone-to-Bluetooth Hub
).
•
Connect the GN 1000 to the AUX socket
on the Bluetooth Hub (see
GN 1000 User
Manual
).
•
Connect the power supply
to your Bluetooth Hub’s power supply socket
.
•
Connect the power supply
to the wall power socket.
•
You can use the ‘wire guide’ at the bottom of the Bluetooth Hub to neatly guide the
cable from the desk phone to the wall phone plug.
The green LED
indicates that the Bluetooth Hub power is on.
Please refer to the GN 1000 User Manual for directions on how to set up your GN 1000.
When the LED
is green and the GN 1000 is installed, please move on to “Adjust setting
with a test call from your desk phone” instructions.
In the unlikely event that the Bluetooth Hub is not OK, its LED
will flash red.
•
First, try disconnecting and reconnecting the Bluetooth Hub from the power source.
•
If the LED
is still flashing red, you must reset your Bluetooth Hub.
o
Press and hold
the Bluetooth Hub reset button
.
o The reset light will turn solid red for 3 seconds, and then turn green.
•
If the LED is still flashing red, after disconnect and reset, please contact your dealer.
IMPORTANT:
Following reset, you must pair your Bluetooth Hub and headset.
17
English