Jensen VM9020TS Operation Manual - Page 12
Operating Instructions - wire setup
View all Jensen VM9020TS manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 12 highlights
OPERATING INSTRUCTIONS Power On / Off Press the /MUTE button (1) to turn the unit on. The buttons on the front of the unit will light up. Press and hold the /MUTE button (1) on the front panel or the POWER button (4) on the remote to power off the unit. Audible Beep Confirmation An audible beep tone confirms each function selection. The beep tone cannot be disabled. Mute Press the /MUTE button (1) on the front panel or remote (3) to mute the volume from the unit. Press the MUTE button again to restore the volume. The mute icon flashes on the right side of the screen. Adjusting the volume or using any of the audio set-up features cancels the mute function. Playing Source Selection Press the SRC button (11) on the remote to change between available playing sources in the following order: TUNER, DVD, AUX IN or CAMERA (rear view video camera). The playing mode is displayed on the screen. Press the MENU/SRC button (11) on the unit to access the playing source menu. Use the direction buttons on the joystick (6, 7, 8, 9) or remote control (14, 17, 18, 19, 22) to select a playing source, then press the button (18) or the joystick enter button (5) to enter the selected source. AUX IN Mode An external peripheral device can be connected to this unit via RCA output and "AUX-IN". CAMERA Mode "CAMERA" mode is only available if the camera is connected and during reverse driving. To install a rear view video camera, connect the video input cable to the camera output cable. Volume Adjustment To increase the volume level, press the VOL + button (3) on the front panel or remote control. To decrease the volume level, press the VOL - button (4) on the front panel or remote control.The volume ranges from "0" to "40". When the volume level reaches "0" or "40", a triple beep sounds, indicating that the adjustment limit has been reached. The screen displays the volume level for 3 seconds. Programmable Turn-On Volume This feature allows the user to select a turn-on volume setting regardless of the volume setting prior to turning the unit off. To program a specific volume level, push and hold the AUDIO button (2) while the yellow volume bar is displayed on the screen. The unit will beep two times to confirm your turnon volume setting. Audio Control Menu The Audio Control feature allows you to easily adjust your audio system to meet the acoustical characteristics of your vehicle, which vary depending on the type of vehicle and its measurements. To get the best possible sound quality from your new system, be sure to adjust the settings for the speakers as well. Proper setting of the Fader and Balance boosts the effects of the cabin equalizer. Accessing the Audio Control Menu Press the AUDIO/LOC button (2) on the front panel to display the "AUDIO" menu. Selecting an Audio Feature for Adjustment Press the ( )/( ) buttons (8, 9) on the joystick or the ( )/ ( ) buttons (17, 19) on the remote control to select the audio feature to be adjusted. Adjusting an Audio Feature Press the or buttons (14, 22) on the remote control or the or buttons (6, 7) on the joystick to adjust the selected feature to the desired setting. Table 4: Audio Adjustments Audio Function Adjustable Range EQ Bass Treble Fade Bal SW Loud User Flat Jazz Pop Classical Rock Vocal -14 to +14 -14 to +14 -9 to +9 -9 to +9 -7 to +7 Off, 1-4 NOTE: The Bass and Treble levels are only adjustable when EQ is set to "User" mode. VM9020TS The Loud function compensates for deficiencies in sound ranges at low levels. Loudness levels range from 1-4 or "off". When the Loud function is on, LOUD is displayed on the screen. Exiting the Audio Control Menu Press and hold the AUDIO/LOC button (2) or stop making adjustments for a few seconds to exit the audio control menu. Six-Channel Audio Control NOTE: Before adjusting the volume of any speaker, please refer to "Surround Setup" on page 18. Table 5: 6-Channel Audio Adjustments Item Adjustable Range Master Volume Front Left Channel Volume Front Right Channel Volume Rear Left Channel Volume Rear Right Channel Volume Center Channel Volume Subwoofer Volume 00 to 40 -10 to +10 -10 to +10 -10 to +10 -10 to +10 -10 to +10 -10 to +10 Rear Zone If a monitor is installed in the rear zone and connected to the rear zone AV output, passengers in the back seat can control the DVD output using the rear zone remote control. See "Multi-Zone Remote Control" on page 8 for instructions. System Reset To correct a system halt or other illegal operation, use the tip of a pen to press [RESET] Button the RESET button (25) located on the front bottom-left corner of the TFT screen. After a system reset, the unit restores all factory default settings. NOTE: If the unit is reset while a DVD is playing, the DVD resumes play once the reset is complete. Line Mute If the "MUTE" wire is connected, audio output mutes when a telephone call is received by the car phone or when verbal navigation is performed. See "Wiring" on page 3. 10