Kenmore 4102 Use and Care Guide - Page 16

dbQdb

Get Kenmore 4102 - Elite 30 in. Slide-In Electric Range PDF manuals and user guides View all Kenmore 4102 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

Setting Oven Controls Setting the Clock The _ pad is used to set the clock. The clock may be set for 12 or 24 hour time of clay operation. The clock has been preset at the factory for the 12 hour operation. When the range is first plugged in, or when the power supply to the range has been interrupted, the timer in the display will flash (See Fig. 1). INSTRUCTIONS To set the clock (example below for 1:30) 1. Press @. "CLO" will appear in the display (Figure 2). 2. Press (_ (_) (_ pads to set the time of day to 1:30 (Figure 3). "CLO" will stay in the display. Press _ START'":CLO" will disappear and the clock will start (Figure 4). Changing between 12 or 24 hour time of day display 1. Press and hold @ for 7 seconds, "CLO" will appear in the display. After 3 seconds i_ will appear in the display indicating that the cooktop lockout is active (Figure 5). CONTINUE holding the pad until "12h" (Figure 6) or "24h" (Figure 7) appears in the display and the control beeps once. 2. Press _ to switch between the 12 and 24 hour time of day display. The display will show either "12h" (Figure 6) or "24h" (Figure 7). 3. Press to accept the change or press _ to reject the change. I_1will disappear from the display. 4. Reset the correct time as described in To set the Clock above. Please note that if the 24 hour time of day mode was chosen, the clock will now display time from 0:00 through 23:59 hours. PRESS O dbQdb O for 7 seconds @ or( @ Figure 1 DISPLAY Figure 2 Figure 3 Figure 4 Figure 5 Figure 6 Figure 7 16

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
Setting
Oven Controls
Setting
the
Clock
The _
pad is used to set the clock. The clock may be set for 12 or 24 hour time of
clay
operation.
The clock has been preset at the factory for the 12 hour operation.
When the
range is first plugged
in, or when the power supply to the range has been
interrupted,
the
timer in the display will flash (See Fig. 1).
Figure 1
INSTRUCTIONS
To set the clock
(example
below
for
1:30)
1.
Press @.
"CLO"
will appear in the
display (Figure 2).
2.
Press (_
(_)
(_
pads to set the time of day to 1:30
(Figure
3). "CLO"
will stay in the display.
Press _ START':
"CLO"
will disappear
and the clock will start (Figure 4).
Changing
between
12
or
24 hour
time
of
day display
1.
Press and hold @
for 7 seconds,
"CLO"
will appear in the
display. After 3 seconds i_ will appear in the display indicating
that the cooktop lockout is active (Figure 5). CONTINUE
holding
the pad until "12h"
(Figure 6) or "24h"
(Figure 7) appears in the
display and the control beeps once.
2.
Press _
to switch between
the 12 and 24 hour time of day
display. The display will show either "12h"
(Figure 6) or "24h"
(Figure 7).
3.
Press
to accept the change or press _
to reject the
change. I_1will disappear from the display.
4.
Reset the correct time as described
in To set the Clock
above.
Please note that if the 24 hour time of day mode was chosen,
the clock will now display time from 0:00 through 23:59 hours.
PRESS
O
dbQdb
O
for 7
seconds
@
or(
@
DISPLAY
Figure 2
Figure 3
Figure 4
Figure 5
Figure 6
Figure 7
16