Kenmore SI3209ZA Use and Care Guide - Page 20

Manually

Lighting

Your

Grill

By Paper

Match

To light your gas grill by match,

insert a match into the

Lighting

Stick and follow steps 1 through

5 of the Grill

Lighting

Instructions.

Then,

light the match

and place

Lighting

Stick through

the Cooking

Grid on the grill as

shown below. Turn the nearest Control

Knob

to the Hi

setting

to release gas. The

Burner

should

light

immedi-

ately.

Match

\\

\

\

(Note:the

Lighting

Stick

is placed

in

the

drawer.)

Never

lean

over

the

grill

cooking

area

while

lighting

your

gas

grill.

Keep

your

face

and

body

a

safe

distance

(at

least

18

inches)

from

the

front

of

grill

when

lighting

your

grill

by

match.

Should

a FLASHBACK

fire

occur

in or around

the Burner Tubes, follow

the instructions

below.

Failure

to

comply

with these

instructions

could

result

in a fire

or explosion

that could

cause

serious

bodily

injury, death,

or property

damage.

•

Shut

off

gas supply

to the

gas grill.

•

Turn

the Control

Knobs

to

OFF

position.

•

Open

the

Grill

Lid.

•

Put out any flame

with

a Class

B fire

extinguisher.

•

Once

the grill

has cooled

down,

clean

the Burner

Tubes

and Burners

according

to

the

cleaning

instructions

in this

Use

and Care

Guide.

If ignition does not occur

in 5 seconds,

turn the Control

Knob(s)

and gas source

OFF

and conduct

a leak test

as explained

in the Use and Care section of this guide.

If no

leaks

are detected,

wait

5 minutes

for any

gas

to clear and repeat

the lighting procedure.

Troubleshooting

If

the

grill

fails

to

light

:

1. Turn gas off at source

and turn Control

Knobs to OFF.

Wait

at least 5 minutes

for gas to clear, then

retry.

2. If your

grill still fails

to light,

check

gas supply

and

connections.

3. Repeat

lighting

procedure.

If your

grill

still fails

to

operate,

turn

the gas off at source,

turn

the

Control

Knobs

to OFF,

then

check

the

following:

[]

Misalignment

of Burner

Tubes over Orifices

Correction:

Reposition

Burner Tubes over Orifices.

[]

Obstruction

in gas line

Correction:

Remove fuel line from grill. Do not smoke!

Open gas supply for one second

to clear any obstruction

from fuel line. Close off gas supply at source

and recon-

nect fuel line to grill.

[]

Plugged

Orifice

Correction:

Remove

Burners

from grill by removing

the

screw

from

the rear of each

Burner

using

Phillips Head

Screwdriver.

Carefully lift each Burner

up and away from

gas valve Orifice. Remove

the Orifice from

gas valve and

gently clear any obstruction

with a fine wire. Then

reinstall all Orifices,

Burners,

screws

and

cooking

components.

[]

If an obstruction

is suspected

in Gas Valves

or Manifold,

call the Grill Information

Center

1-888-317-7642

8am to

8pm CST, Monday

through

Friday.

[]Obstruction

in Burner

Tubes

Correction:

Follow

the Burner

Tube cleaning

procedure

on page

27 of this Use and Care Guide.

[]

Misalignment

of Ignitor on

Burner

Correction:

Check for proper

position

of the Electrode

Tip as shown

in step

6 page

14. The

gap between the

Spark

Electrode

Tip and

Spark

Receiver

should

be

approximately

3/16". Adjust

if necessary.

With

the gas

supply

closed, turn any Main Burner

Control

Knob to

then push in and watch

for the presence

of a spark at

the

Electrode.

[]

Disconnected

Electric

Wires

Correction:

Inspect the Ignitor Junction

Box found behind

the Control

Panel. Connect

loose

Electric wires to

Junction

Box and try to light the grill.

[]

WeakAA

battery

Correction:

Unscrew

the Ignitor Cap and replace the

battery.

[]

If the

grill

still does

not

light

you

may

need

to

purge

air

from

the

gas

line

or

reset

the

regulator

excess

gas

flow

device.

Note:

This

procedure

should

be

done

every

time

a

new

LP

Gas

tank

is connected

to

your

grill.

To

purge

air

from

your

gas

line

and/or

reset

the

regulator

excess

gas

flow

device:

[]

Turn

Control

Knobs

to

the

OFF

position.

[]

Turn

off

the

gas

at the

tank

valve.

[]

Disconnect

regulator

from

LP

Gas

tank.

[]

Let

unit

stand

5

minutes

to

allow

air

to

purge.

[]

Reconnect

regulator

to

the

LP

Gas

tank.

[]

Turn

tank

valve on

SLOWLY

1/4

of a turn.

[]

[]

[]

20

Open

the

Grill

Lid.

Push and

turn

the

Left Main

Burner

Control

Knob to

#y.

Press

Electric

Ignitor

for

3-4

seconds

to

light

the

burners.

Kenmore SI3209ZA Use and Care Guide - Page 20

and Burners

Page 20 highlights