Kenwood DNX4280BT User Manual - Page 82

Controlling General Audio, DSP select

Get Kenwood DNX4280BT PDF manuals and user guides View all Kenwood DNX4280BT manuals
Add to My Manuals
Save this manual to your list of manuals

Page 82 highlights

DSP select You can select whether using DSP (Digital Signal Processor) System. 1 Touch [Bypass] or [Through] of [DSP Select] in the Audio SETUP screen. Return to the Top page Audio Setting Up 2 Set each item as follows. Bypass There is no effect by DSP. Through There is an effect by DSP. NOTE • When the mode is set to [Bypass], DSP System cannot be adjusted. Controlling General Audio 1 Touch [Audio Control]. Fader #/Balance # Adjust the volume balance around the touched area. [2] and [3] adjust the right and left volume balance. [5] and [∞] adjust the front and rear volume balance. Volume Offset* Finely adjust the volume of the current source to minimize the difference in volume between different sources. Subwoofer Level Adjusts the subwoofer volume. This setting is not available when subwoofer is set to "None". See Speaker setup (P.78). Bass Boost Sets the amount of bass boost among "OFF"/ "Step1"/ "Step2". Loudness Turns the loudness control function on or off. If turned on, high and low tones are automatically enhanced during low volume. Settable only when zone function (P.84) is set to off. * If you have increased the volume first, then reduced the volume using the "Volume Offset", the sound generated if you suddenly switch to another source may be extremely loud. 81

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
81
Return to the Top page
Audio Setting Up
DSP select
You can select whether using DSP (Digital
Signal Processor) System.
1
Touch [Bypass] or [Through] of [DSP
Select] in the Audio SETUP screen.
Bypass
There is no effect by DSP.
Through
There is an effect by DSP.
NOTE
• When the mode is set to [Bypass], DSP System
cannot be adjusted.
Controlling General Audio
1
Touch [Audio Control].
2
Set each item as follows.
Fader #/Balance #
Adjust the volume balance around the
touched area.
[
2
] and [
3
] adjust the right and left volume
balance.
[
5
] and [
∞
] adjust the front and rear volume
balance.
Volume Offset*
Finely adjust the volume of the current source
to minimize the difference in volume between
different sources.
Subwoofer Level
Adjusts the subwoofer volume. This setting is
not available when subwoofer is set to“None”.
See
Speaker setup (P.78)
.
Bass Boost
Sets the amount of bass boost among “OFF”/
“Step1”/“Step2”.
Loudness
Turns the loudness control function on or
off. If turned on, high and low tones are
automatically enhanced during low volume.
Settable only when zone function
(P.84)
is set
to off.
* If you have increased the volume first, then
reduced the volume using the “Volume
Offset”, the sound generated if you
suddenly switch to another source may be
extremely loud.