Kenwood DNX531VBT User Manual - Page 43

Controlling General Audio, Equalizer Control, operation

Get Kenwood DNX531VBT PDF manuals and user guides View all Kenwood DNX531VBT manuals
Add to My Manuals
Save this manual to your list of manuals

Page 43 highlights

Return to the Top page Audio Setting Up Controlling General Audio 1 Touch [Audio Control]. * If you have increased the volume first, then reduced the volume using the "Volume Offset", the sound generated if you suddenly switch to another source may be extremely loud. 2 Set each item as follows. Fader #/Balance # Adjust the volume balance around the touched area. [2] and [3] adjust the right and left volume balance. [5] and [∞] adjust the front and rear volume balance. Volume Offset* Finely adjust the volume of the current source to minimize the difference in volume between different sources. Subwoofer Level Adjusts the subwoofer volume. This setting is not available when subwoofer is set to "None". See Speaker setup (P.82). Loudness Turns the loudness control function on or off. If turned on, high and low tones are automatically enhanced during low volume. Settable only when zone function (P.86) is set to off. 84 Equalizer Control You can adjust equalizer by selecting the optimized setting for each category. 1 Touch [Equalizer]. Return to the Top page Audio Setting Up Controlling equalizer manually 1 Touch [Tone] in the Equalizer screen. 2 Set each item as follows. Equalizer screen appears. operation Controlling EQ curves 1 Select EQ curve from [Natural], [Rock], [Pops], [Easy], [Top40], [Jazz], and [User] using [2] and [3]. Controlling SystemQ-Ex Selects items to be adjusted for tone curve setup. If you turn off this setting, only Level can be set up for tone curves. 1 Touch [ON] or [OFF] of [SystemQ-Ex]. FREQ Adjusts the center frequency for each range. Setting values are as follows. Bass: 40Hz/50Hz/60Hz/70Hz/80Hz/100Hz/120 Hz/150Hz (Default is "100Hz".) Middle: 500Hz/1kHz/1.5kHz/2kHz (Default is "1kHz".) Treble: 10kHz/12.5kHz/15kHz/17.5kHz (Default is "12.5kHz".) LEVEL Adjusts the level of each range. Each setting value is within -8dB and 8dB and default is "0dB". Q Factor Adjust Q value for bass and middle. Setting values are as follows. Bass: 1/1.25/1.5/2 (Default is "1".) Middle: 1/2 (Default is "1".) Bass DC EXT Turns Bass DC EXT on or off. Default is "OFF". If you select "ON", the bass center frequency is extended to the low register by approximately 20%. [Flat] Tone level becomes 0 (flat). Subwoofer Level Adjusts the subwoofer volume. This setting is not available when subwoofer is set to "OFF". See Speaker setup (P.82). 85

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
84
84
85
Return to the Top page
Audio Setting Up
Return to the Top page
Audio Setting Up
Controlling General Audio
1
Touch [Audio Control].
2
Set each item as follows.
Fader #/Balance #
Adjust the volume balance around the
touched area.
[
2
] and [
3
] adjust the right and left volume
balance.
[
5
] and [
∞
] adjust the front and rear volume
balance.
Volume Offset*
Finely adjust the volume of the current source
to minimize the difference in volume between
different sources.
Subwoofer Level
Adjusts the subwoofer volume. This setting is
not available when subwoofer is set to “None”.
See
Speaker setup (P.82)
.
Loudness
Turns the loudness control function on or
off. If turned on, high and low tones are
automatically enhanced during low volume.
Settable only when zone function
(P.86)
is
set to off.
* If you have increased the volume first, then
reduced the volume using the “Volume
Offset”, the sound generated if you
suddenly switch to another source may be
extremely loud.
Equalizer Control
You can adjust equalizer by selecting the
optimized setting for each category.
1
Touch [Equalizer].
Equalizer screen appears.
operation
Controlling EQ curves
1
Select EQ curve from [Natural],
[Rock], [Pops], [Easy], [Top40], [Jazz],
and [User] using [
2
] and [
3
].
Controlling SystemQ-Ex
Selects items to be adjusted for tone curve
setup. If you turn off this setting, only Level
can be set up for tone curves.
1
Touch [ON] or [OFF] of [SystemQ-Ex].
Controlling equalizer manually
1
Touch [Tone] in the Equalizer screen.
2
Set each item as follows.
FREQ
Adjusts the center frequency for each range.
Setting values are as follows.
Bass:
40Hz/50Hz/60Hz/70Hz/80Hz/100Hz/120
Hz/150Hz (Default is “100Hz”.)
Middle:
500Hz/1kHz/1.5kHz/2kHz (Default is
“1kHz”.)
Treble:
10kHz/12.5kHz/15kHz/17.5kHz (Default
is“12.5kHz”.)
LEVEL
Adjusts the level of each range.
Each setting value is within -8dB and 8dB and
default is“0dB”.
Q Factor
Adjust Q value for bass and middle.
Setting values are as follows.
Bass:
1/1.25/1.5/2 (Default is“1”.)
Middle:
1/2 (Default is“1”.)
Bass DC EXT
Turns Bass DC EXT on or off. Default is “OFF”.
If you select “ON”, the bass center frequency is
extended to the low register by approximately
20%.
[Flat]
Tone level becomes 0 (flat).
Subwoofer Level
Adjusts the subwoofer volume. This setting is
not available when subwoofer is set to “OFF”.
See
Speaker setup (P.82)
.