Kenwood DPX500BT Quick Start Guide - Page 8

Installation accessories, Before Installation, Installation Procedure - reset

Page 8 highlights

Installation accessories 1 .....1 2 .....1 3 .....1 4 .....2 5 .....6 6 .....6 7 (DPX500BT only) 3 m (9.5 ft) .....1 Installation Procedure 1. To prevent a short circuit, remove the key from the ignition and disconnect the - battery. 2. Make the proper input and output wire connections for each unit. 3. Connect the speaker wires of the wiring harness. 4. Connect the wiring harness wires in the following order: ground, battery, ignition. 5. Connect the wiring harness connector to the unit. 6. Install the unit in your car. 7. Reconnect the - battery. 8. Press the reset button. 8 | Quick Start Guide Before Installation 2WARNING If you connect the ignition wire (red) and the battery wire (yellow) to the car chassis (ground), you may cause a short circuit, that in turn may start a fire. Always connect those wires to the power source running through the fuse box. ¤ CAUTION • Mounting and wiring this product requires skills and experience. For safety's sake, leave the mounting and wiring work to professionals. • Make sure to ground the unit to a negative 12V DC power supply. • Do not install the unit in a spot exposed to direct sunlight or excessive heat or humidity. Also avoid places with too much dust or the possibility of water splashing. • Do not use your own screws. Use only the supplied screws. Using wrong screws, could damage the unit. • If the power is not turned ON ("PROTECT" is displayed), the speaker wire may have a shortcircuit or touched the chassis of the vehicle and the protection function may have been activated. Therefore, the speaker wire should be checked. • If your car's ignition key switch does not have an ACC position, connect the ignition wires to a power source that can be turned on and off with the ignition key. If you connect the ignition wires to a constant-voltage power source, as with battery wires, the battery may die. • If the console has a lid, make sure to install the unit so that the faceplate will not hit the lid when it is closed or opened. • If the fuse blows, first make sure the wires are not touching other parts to cause a short circuit, and then replace the old fuse with one with a new the same rating. • Insulate unconnected wires with vinyl tape or other similar materials. To prevent a short circuit, do not remove the caps on the ends of the unconnected wires and terminals. • Connect the speaker wires correctly to the corresponding terminals. The unit may be damaged or fail to work if you share the - wires or ground them to any metal part in the car. • When connecting only two speakers, connect the connectors either to both of the front output terminals or to both of the rear output terminals (do not mix front and rear terminals). For example, if you connect the + connector of the left speaker to a front output terminal, do not connect the connector to a rear output terminal. • After the installing the unit, check whether the brake lamps, blinkers, wipers, etc. on the car are working properly.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48

8
|
Quick Start Guide
Installation accessories
1
.....
1
2
.....
1
3
.....
1
4
.....
2
5
.....
6
6
.....
6
7
(DPX500BT only)
3 m (9.5 ft)
.....
1
2
WARNING
If you connect the ignition wire (red) and the battery
wire (yellow) to the car chassis (ground), you may
cause a short circuit, that in turn may start a fire.
Always connect those wires to the power source
running through the fuse box.
¤
CAUTION
Mounting and wiring this product requires skills and
experience. For safety’s sake, leave the mounting and
wiring work to professionals.
Make sure to ground the unit to a negative 12V DC
power supply.
Do not install the unit in a spot exposed to direct
sunlight or excessive heat or humidity. Also avoid
places with too much dust or the possibility of water
splashing.
Do not use your own screws. Use only the supplied
screws. Using wrong screws, could damage the unit.
If the power is not turned ON (“PROTECT” is
displayed), the speaker wire may have a short-
circuit or touched the chassis of the vehicle and
the protection function may have been activated.
Therefore, the speaker wire should be checked.
If your car’s ignition key switch does not have an
ACC position, connect the ignition wires to a power
source that can be turned on and off with the
ignition key. If you connect the ignition wires to
a constant-voltage power source, as with battery
wires, the battery may die.
If the console has a lid, make sure to install the unit
so that the faceplate will not hit the lid when it is
closed or opened.
If the fuse blows, first make sure the wires are not
touching other parts to cause a short circuit, and
then replace the old fuse with one with a new the
same rating.
Insulate unconnected wires with vinyl tape or other
similar materials. To prevent a short circuit, do not
remove the caps on the ends of the unconnected
wires and terminals.
Connect the speaker wires correctly to the
corresponding terminals. The unit may be damaged
or fail to work if you share the
-
wires or ground
them to any metal part in the car.
When connecting only two speakers, connect
the connectors either to both of the front output
terminals or to both of the rear output terminals
(do not mix front and rear terminals). For example,
if you connect the
+
connector of the left speaker
to a front output terminal, do not connect the
-
connector to a rear output terminal.
After the installing the unit, check whether the brake
lamps, blinkers, wipers, etc. on the car are working
properly.
Before Installation
Installation Procedure
1. To prevent a short circuit, remove the key from the
ignition and disconnect the
-
battery.
2. Make the proper input and output wire
connections for each unit.
3. Connect the speaker wires of the wiring harness.
4. Connect the wiring harness wires in the following
order: ground, battery, ignition.
5. Connect the wiring harness connector to the unit.
6. Install the unit in your car.
7. Reconnect the
-
battery.
8. Press the reset button.