Kenwood KDC-X395 Instruction Manual - Page 34

Troubleshooting - wiring

Get Kenwood KDC-X395 PDF manuals and user guides
UPC - 019048193025
View all Kenwood KDC-X395 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

Installation the Microphone Unit (KDC-X695 only) 1 Check the installation position of the microphone H. 2 Remove oil and other dirt from the H installation surface. 3 Install the microphone. 4 Wire the microphone cable up to the hands-free box with it secured at several positions using tape or the like. ■ Install the microphone as far away as possible from the cell-phone. Peel the release coated paper of double-face adhesive tape to fix on the place shown above. Fix a cable with a commercial item of tape. Adjust the direction of the microphone to the driver. Troubleshooting Symptom Sound cannot be heard. "PROTECT" appears and no operations can be done. The unit does not work at all. Radio reception is poor. / Static noise while listening to the radio. "IN" flashes. CD-R/CD-RW cannot be played back and tracks cannot be skipped. Disc sound is sometimes interrupted. "NA FILE" appears. "NO DISC" appears. "TOC ERROR" appears. "ERROR 77" or "ERROR 99" appears. Remedy/Cause Adjust the volume to the optimum level. / Check the cords and connections. Check to be sure the terminals of the speaker leads are covered with insulating tape properly, then reset the unit. If "PROTECT" does not disappear, consult your nearest service center. Reset the unit. Connect the antenna firmly. / Pull the antenna out all the way. The CD player is not operating properly. Reinsert the disc properly. If the condition did not improve, turn off the unit and consult your nearest service center. Insert a finalized CD-R/CD-RW (finalize with the component which you used for recording). Stop playback while driving on rough roads. / Change the disc. / Check the cords and connections. The unit is playing an unsupported audio file. Insert a playable disc into the loading slot. The CD is quite dirty. / The CD is upside-down. / The CD is scratched a lot. Try another disc instead. The unit is malfunctioning for some reason. Press the reset button on the unit. If the "ERROR 77"/ "ERROR 99" code does not disappear, consult your nearest service center. 34 English

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
34
English
Installation the Microphone Unit (KDC-X695 only)
1
Check the installation position of the
microphone
H
.
2
Remove oil and other dirt from the
installation surface.
3
Install the microphone.
4
Wire the microphone cable up to the
hands-free box with it secured at several
positions using tape or the like.
■
Install the microphone as far away as
possible from the cell-phone.
H
Fix a cable with a commercial
item of tape.
Peel the release coated
paper of double-face
adhesive tape to fix on
the place shown above.
Adjust the direction
of the microphone to
the driver.
Troubleshooting
Symptom
Remedy/Cause
Sound cannot be heard.
Adjust the volume to the optimum level. / Check the cords and connections.
“PROTECT” appears and no operations can
be done.
Check to be sure the terminals of the speaker leads are covered with insulating tape
properly, then reset the unit. If “PROTECT” does not disappear, consult your nearest
service center.
The unit does not work at all.
Reset the unit.
Radio reception is poor. / Static noise while
listening to the radio.
Connect the antenna firmly. / Pull the antenna out all the way.
“IN” flashes.
The CD player is not operating properly. Reinsert the disc properly. If the condition did
not improve, turn off the unit and consult your nearest service center.
CD-R/CD-RW cannot be played back and
tracks cannot be skipped.
Insert a finalized CD-R/CD-RW (finalize with the component which you used for
recording).
Disc sound is sometimes interrupted.
Stop playback while driving on rough roads. / Change the disc. / Check the cords and
connections.
“NA FILE” appears.
The unit is playing an unsupported audio file.
“NO DISC” appears.
Insert a playable disc into the loading slot.
“TOC ERROR” appears.
The CD is quite dirty. / The CD is upside-down. / The CD is scratched a lot. Try another
disc instead.
“ERROR 77” or “ERROR 99” appears.
The unit is malfunctioning for some reason. Press the reset button on the unit. If the
“ERROR 77”/ “ERROR 99” code does not disappear, consult your nearest service center.