Kenwood KDC-X395 Instruction Manual - Page 35

Symptom, Remedy/Cause - protect

Page 35 highlights

Symptom Remedy/Cause "COPY PRO" appears. A copy-protected file is played. "READ ERROR" appears. Copy the files and folders for the USB device again. If the error message is still displayed, initialize the USB device or use other USB devices. "NO DEVICE" appears. No USB device is connected. Connect a USB device, and change the source to USB again. "NO MUSIC" or "ERROR 15" appears. The connected USB device contains no playable audio file. / Media was played that does not have data recorded that the unit can play. "NA DEVICE" appears. Connect a supported USB device, and check the connections. "USB ERROR" appears. Remove the USB device, turn the unit off, then turn it on again. If the unit still showing the same display, try to connect another USB device. "iPod ERROR" appears. Reconnect the iPod. / Confirm that the software for the iPod is the latest version. / Reset the iPod. Noise is generated. Skip to another track or change the disc. Tracks cannot play back as you have intended Playback order is determined when files are recorded. them to play. "READING" keeps flashing. Longer readout time is required. Do not use too many hierarchies and folders. Elapsed playing time is not correct. This is caused by how the tracks are recorded. The number of songs contained in "SONGS" Podcast files are not counted in this unit as this unit does not support the playback of category of this unit is different from that podcast files. contained in "SONGS" category of iPod. Correct characters are not displayed (e.g. This unit can only display letters (upper case), numbers, and a limited number of album name). symbols. Bluetooth Symptom Remedy/Cause The hands-free talk volume is low. The hands-free talk volume can be adjusted independently. Adjust it during handsfree talk. [MIC GAIN], [NR LEVEL] and [EC LEVEL] of (page 21). No beep is heard at reception of an incoming No beep is heard depending on the type of your cell-phone. The [CALL BEEP] of call. (page 21) is set ON. Voice is not recognized. ■ The vehicle window is open. If the surrounding noise is large, voice cannot be recognized properly. Close the vehicle windows to reduce noise. ■ Small voice. If voice is too small, it cannot be recognized properly. Speak into the microphone a little more loudly and naturally. ■ The person uttering the voice tag is not the one who registered the it. Only the voice of the person who registered the voice tag can be recognized. "NO NUMBER" appears. The calling party does not notify a caller ID. / There is no phone number data. "NO DATA" appears. There is no outgoing call list. / There is no incoming call list. / There is no missed call list. / There is no phone book list. "NO ENTRY" appears. The cell-phone has not been registered (pairing). "HF DISCONCT" appears. The unit cannot communicate with the cell-phone. Continued to next page English 35

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112

English
35
Continued to next page
Symptom
Remedy/Cause
“COPY PRO” appears.
A copy-protected file is played.
“READ ERROR” appears.
Copy the files and folders for the USB device again. If the error message is still
displayed, initialize the USB device or use other USB devices.
“NO DEVICE” appears.
No USB device is connected. Connect a USB device, and change the source to USB
again.
“NO MUSIC” or “ERROR 15” appears.
The connected USB device contains no playable audio file. / Media was played that
does not have data recorded that the unit can play.
“NA DEVICE” appears.
Connect a supported USB device, and check the connections.
“USB ERROR” appears.
Remove the USB device, turn the unit off, then turn it on again. If the unit still showing
the same display, try to connect another USB device.
“iPod ERROR” appears.
Reconnect the iPod. / Confirm that the software for the iPod is the latest version. /
Reset the iPod.
Noise is generated.
Skip to another track or change the disc.
Tracks cannot play back as you have intended
them to play.
Playback order is determined when files are recorded.
“READING” keeps flashing.
Longer readout time is required. Do not use too many hierarchies and folders.
Elapsed playing time is not correct.
This is caused by how the tracks are recorded.
The number of songs contained in “SONGS”
category of this unit is different from that
contained in “SONGS” category of iPod.
Podcast files are not counted in this unit as this unit does not support the playback of
podcast files.
Correct characters are not displayed (e.g.
album name).
This unit can only display letters (upper case), numbers, and a limited number of
symbols.
Bluetooth
Symptom
Remedy/Cause
The hands-free talk volume is low.
The hands-free talk volume can be adjusted independently. Adjust it during hands-
free talk.
[MIC GAIN]
,
[NR LEVEL]
and
[EC LEVEL]
of <Bluetooth Setup> (page 21).
No beep is heard at reception of an incoming
call.
No beep is heard depending on the type of your cell-phone. The
[CALL BEEP]
of
<Bluetooth Setup> (page 21) is set ON.
Voice is not recognized.
The vehicle window is open. If the surrounding noise is large, voice cannot be
recognized properly. Close the vehicle windows to reduce noise.
Small voice. If voice is too small, it cannot be recognized properly. Speak into the
microphone a little more loudly and naturally.
The person uttering the voice tag is not the one who registered the it. Only the
voice of the person who registered the voice tag can be recognized.
“NO NUMBER” appears.
The calling party does not notify a caller ID. / There is no phone number data.
“NO DATA” appears.
There is no outgoing call list. / There is no incoming call list. / There is no missed call
list. / There is no phone book list.
“NO ENTRY” appears.
The cell-phone has not been registered (pairing).
“HF DISCONCT” appears.
The unit cannot communicate with the cell-phone.