Kenwood KDC-X879 Instruction Manual - Page 21

Panel Position Setting, Theft Deterrent Panel, Press the [4] PNL KDC-MP925/X879/ [5]

Get Kenwood KDC-X879 PDF manuals and user guides View all Kenwood KDC-X879 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

Panel Position Setting Setting the angle or back-forward position of the control panel. 1 Select the key function section Press the [NEXT] button. Repeatedly press the button until "PNL" is displayed above the [4]/ [5] button. 2 Enter Panel Position Setting mode Press the [4] ("PNL") (KDC-MP925/X879)/ [5] ("PNL") (KDC-X979) button. 3 Select the item for adjustment Press the desired [2] - [5] button. Each time the button is pressed the items that can be adjusted switch as shown below. Adjustment Item The panel tilts upwards. The panel tilts downwards. The panel slides backward. The panel slides forward. Button [2] [3] [4] [5] Display "ANG-" "ANG+" "SLD-" "SLD+" 4 Exit Panel Position Setting mode Press the [6] ("RTN") button. • The control panel may be interfered with the shift lever or another part depending on the angles of the control panel. Set the angle to avoid any interference. • When a hard rubber frame is mounted Do not use with the panel slid in the forward direction. If so, the hard rubber frame will interfere with the panel when the angle is adjusted downward. • No sound is produced while the panel is operating. 2 Remove the Backpanel forward. When 'DSI (Disabled System Indicator)' (page47) is set to ON, DSI blinks. • The back panel is a precision piece of equipment and can be damaged by shocks or jolts. For that reason, keep the back panel in its special storage case while detached. • Do not expose the Backpanel or its storage case to direct sunlight or excessive heat or humidity. Also avoid places with too much dust or the possibility of water splashing. Reattaching the Backpanel 1 Set the Backpanel to the panel bracket. 2 Hold down on the Backpanel until it is locked. Theft Deterrent Panel The Backpanel of the unit can be detached and taken with you, helping to deter theft. Removing the Backpanel 1 Turn the ignition OFF or press the [SRC] button for at least 1 second. Turn OFF the power, and the control panel becomes horizontal. • After the set time passes in 'OFF Wait Time Setting' (page48), the panel is closed. English | 21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
English
|
21
Panel Position Setting
Setting the angle or back-forward position of the
control panel.
1
Select the key function section
Press the [NEXT] button.
Repeatedly press the button until "PNL" is
displayed above the [4]/ [5] button.
2
Enter Panel Position Setting mode
Press the [4] ("PNL") (KDC-MP925/X879)/ [5]
("PNL") (KDC-X979)
button.
3
Select the item for adjustment
Press the desired [2]
—
[5] button.
Each time the button is pressed the items that
can be adjusted switch as shown below.
Adjustment Item
Button
Display
The panel tilts upwards.
[2]
"ANG–"
The panel tilts downwards.
[3]
"ANG+"
The panel slides backward.
[4]
"SLD–"
The panel slides forward.
[5]
"SLD+"
4
Exit Panel Position Setting mode
Press the [6] ("RTN") button.
•
The control panel may be interfered with the shift
lever or another part depending on the angles of the
control panel.
Set the angle to avoid any interference.
•
When a hard rubber frame is mounted
Do not use with the panel slid in the forward
direction.
If so, the hard rubber frame will interfere with the
panel when the angle is adjusted downward.
• No sound is produced while the panel is operating.
Theft Deterrent Panel
The Backpanel of the unit can be detached and
taken with you, helping to deter theft.
Removing the Backpanel
1
Turn the ignition OFF or press the [SRC]
button for at least 1 second.
Turn OFF the power, and the control panel
becomes horizontal.
• After the set time passes in 'OFF Wait Time Setting'
(page48), the panel is closed.
2
Remove the Backpanel forward.
When 'DSI (Disabled System Indicator)' (page47)
is set to ON, DSI blinks.
•
The back panel is a precision piece of equipment and
can be damaged by shocks or jolts. For that reason,
keep the back panel in its special storage case while
detached.
• Do not expose the Backpanel or its storage case to
direct sunlight or excessive heat or humidity. Also
avoid places with too much dust or the possibility of
water splashing.
Reattaching the Backpanel
1
Set the Backpanel to the panel bracket.
2
Hold down on the Backpanel until it is locked.