Kenwood KDC-X879 Instruction Manual - Page 41

Direct Access Tuning, Selecting the Preset Band, Channel Preset Memory, Preset Tuning

Get Kenwood KDC-X879 PDF manuals and user guides View all Kenwood KDC-X879 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

2 Select the item for adjustment Press the desired [2] - [5] button. Each time the button is pressed the items that can be adjusted switch as shown below. Adjustment Item Search down in category Search up in category Search down for channel in selected category Search up for channel in selected category Button Display [2] "CS-" [3] "CS+" [4] "CH-" [5] "CH+" • You cannot operate this unit until all the Category information is acquired. Function of remote Direct Access Tuning Entering the channel and tuning. 1 Enter Direct Access Tuning mode Press the [DIRECT] button on the remote. 2 Enter the channel Press the number buttons. 3 Do Channel Search Press the [4] or [¢] button. Canceling Direct Access Tuning Press the [DIRECT] button on the remote. • If you make no button operation for 10 seconds, the Direct Access Tuning mode is automatically canceled. • You can set up to Channel number 223. • If there is no signal in the input Channel, "NO CHANNEL" appears. • If you cannot receive any signal in the input Channel due to a bad condition on radio wave or another problem, "Acquiring Signal" appears. Channel Preset Memory Putting the channel in the memory. 1 Select the preset band Press the [FM] button. 2 Select the channel to put in the memory Press the [4] or [¢] button. 3 Select the key function section Press the [NEXT] button. Repeatedly press the button until "[1]" - "[6]" are displayed above the [1] - [6] buttons. Refer to 'Notes on Multi-function Key System' (page 9). 4 Put the channel in the memory Press the desired [1] - [6] button for at least 2 seconds. The preset number display blinks 1 time. On each band, 1 channel can be put in the memory on each [1] - [6] button. • Only the channel number is stored. Category information is not stored. Preset Tuning Calling up the channels in the memory. 1 Select the preset band Press the [FM] button. 2 Select the key function section Press the [NEXT] button. Repeatedly press the button until "[1]" - "[6]" are displayed above the [1] - [6] buttons. Refer to 'Notes on Multi-function Key System' (page 9). 3 Call up the channel Press the desired [1] - [6] button. Selecting the Preset Band Press the [FM] button. Each time the button is pressed the preset band switches between the SR1, SR2, SR3 and SR4. English | 41

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
English
|
41
2
Select the item for adjustment
Press the desired [2]
—
[5] button.
Each time the button is pressed the items that
can be adjusted switch as shown below.
Adjustment Item
Button
Display
Search down in category
[2]
"CS–"
Search up in category
[3]
"CS+"
Search down for channel in selected category
[4]
"CH–"
Search up for channel in selected category
[5]
"CH+"
•
You cannot operate this unit until all the Category
information is acquired.
Function of remote
Direct Access Tuning
Entering the channel and tuning.
1
Enter Direct Access Tuning mode
Press the [DIRECT] button on the remote.
2
Enter the channel
Press the number buttons.
3
Do Channel Search
Press the [
4
] or [
¢
] button.
Canceling Direct Access Tuning
Press the [DIRECT] button on the remote.
• If you make no button operation for 10 seconds, the
Direct Access Tuning mode is automatically canceled.
• You can set up to Channel number 223.
• If there is no signal in the input Channel, "NO
CHANNEL" appears.
• If you cannot receive any signal in the input Channel
due to a bad condition on radio wave or another
problem, "Acquiring Signal" appears.
Selecting the Preset Band
Press the [FM] button.
Each time the button is pressed the preset band
switches between the SR1, SR2, SR3 and SR4.
Channel Preset Memory
Putting the channel in the memory.
1
Select the preset band
Press the [FM] button.
2
Select the channel to put in the memory
Press the [
4
] or [
¢
] button.
3
Select the key function section
Press the [NEXT] button.
Repeatedly press the button until "[1]" — "[6]" are
displayed above the [1] — [6] buttons.
Refer to 'Notes on Multi-function Key System'
(page 9).
4
Put the channel in the memory
Press the desired [1] — [6] button for at least
2 seconds.
The preset number display blinks 1 time.
On each band, 1 channel can be put in the
memory on each [1] — [6] button.
•
Only the channel number is stored. Category
information is not stored.
Preset Tuning
Calling up the channels in the memory.
1
Select the preset band
Press the [FM] button.
2
Select the key function section
Press the [NEXT] button.
Repeatedly press the button until "[1]" — "[6]" are
displayed above the [1] — [6] buttons.
Refer to 'Notes on Multi-function Key System'
(page 9).
3
Call up the channel
Press the desired [1] — [6] button.