Kenwood KIV-BT901 Instruction Manual - Page 52

X’Over Setting, Audio Preset Memory, Display, Range

Page 52 highlights

DSP Setup X'Over Setting Fine adjusting the following setting values corresponding to the X'Over values set in the section (page 50). Display Item "X'Over" "Front" "FC" "SLOPE" "Rear" "FC" "SLOPE" "SubWoofer" "FC" "SLOPE" "PHASE" Range Front High Pass Filter Through, 30, 40, 50, 60, 70, 80, 90, 100, 120, 150, 180, 220, 250 (Hz) Front High Pass Slope -6, -12, -18, -24 dB/Oct Rear High Pass Filter Through, 30, 40, 50, 60, 70, 80, 90, 100, 120, 150, 180, 220, 250 (Hz) Rear High Pass Slope -6, -12, -18, -24 dB/Oct Subwoofer Low Pass Filter 30, 40, 50, 60, 70, 80, 90, 100, 120, 150, 180, 220, 250, Through (Hz) Subwoofer Slope -6, -12, -18, -24 dB/Oct Subwoofer Phase Reverse (180°)/ Normal (0°) 1 Select the source Press the [SRC] button repeatedly also switches source. Select a source other than " STANDBY". ✍✍SRC Select mode 2: Press the [SRC] button. Turn the [Volume] knob and press it when the desired item is displayed. 2 Enter Audio Control mode Press the [Volume] knob. 3 Enter X'Over setting mode Turn the [Volume] knob and press it when the desired item is displayed. Select "Detailed Setup" > "X'Over". 4 Select the speaker you want to set Turn the [Volume] knob and press it when the desired item is displayed. Select "Front", "Rear", or "SubWoofer". 5 Select the setting item to adjust Turn the [Volume] knob and press it when the desired item is displayed. 6 Make a setting Turn the [Volume] knob to select a setting value, and then press the [Volume] knob. 7 Repeat steps 3 to 5 to complete the X'Over settings 8 Exit Audio Control mode Press the [MENU] button for at least 1 second. Audio Preset Memory Registering the value setup by Sound Control. 1 Setup Sound Control Refer to the following operations to setup the Sound Control. - Car Type Selection (page 50) - Speaker Setting (page 50) - Car Type Fine Adjustments (page 51) - X'Over Setting (page 52) - Manual Equalizer Control (page 47) - Listening Position Selection (page 48) - Listening Position Fine Adjustments (page 48) 2 Enter Audio preset memory mode Turn the [Volume] knob and press it when the desired item is displayed. Select "Detailed Setup" > "Preset" > "Preset Memory". 3 Select the number to put in the memory Turn the [Volume] knob and press it when the desired item is displayed. Select a preset number. 4 Turn the [Volume] knob and press it when the desired item is displayed. Select "YES". "Completed" is displayed. 5 Exit Audio Control mode Press the [MENU] button for at least 1 second. ⁄ • Register 6 patterns of Audio Preset Memory. • Preset number "1": When you press the Reset, all the sources will be the setting value which is registered. • Preset number "1" and "2": The memory cannot be erased by the Reset button. • This function cannot be registered when the iPod Equalizer set in (page 47). 52 | KIV-BT901/ KIV-701

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88

52
|
KIV-BT901/ KIV-701
DSP Setup
8
Exit Audio Control mode
Press the [MENU] button for at least 1 second.
Audio Preset Memory
Registering the value setup by Sound Control.
1
Setup Sound Control
Refer to the following operations to setup the
Sound Control.
- Car Type Selection (page 50)
- Speaker Setting (page 50)
- Car Type Fine Adjustments (page 51)
- X’Over Setting (page 52)
- Manual Equalizer Control (page 47)
- Listening Position Selection (page 48)
- Listening Position Fine Adjustments (page 48)
2
Enter Audio preset memory mode
Turn the [Volume] knob and press it when the
desired item is displayed.
Select “Detailed Setup”
>
“Preset”
>
“Preset
Memory”.
3
Select the number to put in the memory
Turn the [Volume] knob and press it when the
desired item is displayed.
Select a preset number.
4
Turn the [Volume] knob and press it when the
desired item is displayed.
Select “YES”.
“Completed” is displayed.
5
Exit Audio Control mode
Press the [MENU] button for at least 1 second.
• Register 6 patterns of Audio Preset Memory.
• Preset number “1”:
When you press the Reset, all the sources will be the
setting value which is registered.
• Preset number “1” and “2”:
The memory cannot be erased by the Reset button.
• This function cannot be registered when the iPod
Equalizer set in
<Preset Equalizer Curve Select> (page 47)
.
X’Over Setting
Fine adjusting the following setting values
corresponding to the X’Over values set in the
section
<Speaker Setting> (page 50)
.
Display
Item
Range
“X’Over”
“Front”
“FC”
Front High Pass Filter
Through, 30, 40, 50, 60, 70, 80, 90,
100, 120, 150, 180, 220, 250 (Hz)
“SLOPE”
Front High Pass Slope
-6, -12, -18, -24 dB/Oct
“Rear”
“FC”
Rear High Pass Filter
Through, 30, 40, 50, 60, 70, 80, 90,
100, 120, 150, 180, 220, 250 (Hz)
“SLOPE”
Rear High Pass Slope
-6, -12, -18, -24 dB/Oct
“SubWoofer”
“FC”
Subwoofer Low Pass Filter
30, 40, 50, 60, 70, 80, 90, 100, 120,
150, 180, 220, 250, Through (Hz)
“SLOPE”
Subwoofer Slope
-6, -12, -18, -24 dB/Oct
“PHASE”
Subwoofer Phase
Reverse (180°)/ Normal (0°)
1
Select the source
Press the [SRC] button repeatedly also switches
source.
Select a source other than “
STANDBY”.
SRC Select mode 2: Press the [SRC] button. Turn
the [Volume] knob and press it when the desired
item is displayed.
2
Enter Audio Control mode
Press the [Volume] knob.
3
Enter X’Over setting mode
Turn the [Volume] knob and press it when the
desired item is displayed.
Select “Detailed Setup”
>
“X’Over”.
4
Select the speaker you want to set
Turn the [Volume] knob and press it when the
desired item is displayed.
Select “Front”, “Rear”, or “SubWoofer”.
5
Select the setting item to adjust
Turn the [Volume] knob and press it when the
desired item is displayed.
6
Make a setting
Turn the [Volume] knob to select a setting
value, and then press the [Volume] knob.
7
Repeat steps 3 to 5 to complete the X’Over
settings