Kenwood MP6025 Instruction Manual - Page 37
Troubleshooting Guide, General, Tuner source
UPC - 019048151322
View all Kenwood MP6025 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 37 highlights
Troubleshooting Guide What might seem to be a malfunction in your unit may just be the result of slight misoperation or miswiring. Before calling service, first check the following table for possible problems. General ? The power does not turn ON. ✔ The fuse has blown. ☞ After checking for short circuits in the wires, replace the fuse with one with the same rating. ✔ Speaker cable touches on chassis etc. ☞ Wire or insulate the speaker cable properly and press the reset button. ? There's a source you can't switch. ✔ There's no media inserted. ☞ Set the media you want to listen to. If there's no media in this unit, you can't switch to each source. ✔ The Disc changer isn't connected. ☞ Connect the Disc changer. If the Disc changer isn't connected to it's input terminal, You can't switch to an external disc source. ? The memory is erased when the ignition is turned OFF. ✔ The ignition and battery wire are incorrectly connected. ☞ Connect the wire correctly, referring to the section on 'Connecting Wires to Terminals'. ? There's no loudness effect. ✔ You're using Subwoofer preout. ☞ Loudness has no effect in Subwoofer preout. ? The TEL mute function does not work. ✔ The TEL mute wire is not connected properly. ☞ Connect the wire correctly, referring to the section on 'Connecting Wires to Terminals'. ? The TEL mute function turns ON even though the TEL mute wire is not connected. ✔ The TEL mute wire is touching a metal part of the car. ☞ Pull the TEL mute wire away from the metal part of the car. ? Even if Loudness is turned ON, high-pitched tone isn't compensated for. ✔ Tuner source is selected. ☞ High-pitched tone isn't compensated for when in Tuner source. ? No sound can be heard, or the volume is low. ✔ The fader or balance settings are set all the way to one side. ☞ Center the fader and balance settings. ✔ The input/output wires or wiring harness are connected incorrectly. ☞ Reconnect the input/output wires or the wiring harness correctly. See the section on 'Connecting Wires to Terminals'. ✔ The values of Volume offset are low. ☞ Turn up the Volume offset, referring to the section on 'Audio Control' (page 11). ✔ The 'Built-in Amp Mute Setting' (page 27) is ON. ☞ Turn it OFF. ? The sound quality is poor or distorted. ✔ One of the speaker wires is being pinched by a screw in the car. ☞ Check the speaker wiring. ✔ The speakers are not wired correctly. ☞ Reconnect the speaker wires so that each output terminal is connected to a different speaker. ? The Touch Sensor Tone doesn't sound. ✔ The preout jack is being used. ☞ The Touch Sensor Tone can't be output from the preout jack. ? The Dimmer function doesn't work. ✔ The Dimmer wire isn't connected correctly. ☞ Check the Dimmer wire connection. Tuner source ? Radio reception is poor. ✔ The car antenna is not extended. ☞ Pull the antenna out all the way. ✔ The antenna control wire is not connected. ☞ Connect the wire correctly, referring to the section on 'Connecting Wires to Terminals'. ? The desired frequency can't be entered with the Direct Access Tuning. ✔ A station that can't be received is being entered. ☞ Enter a station that can be received. ✔ You're trying to enter a frequency with a 0.01 MHz unit. ☞ What can be designated in the FM band is to 0.1 MHz. English | 37