KitchenAid KUDD01SSSS Installation Instructions - Page 4
Water Supply Requirements, Electrical Requirements
View all KitchenAid KUDD01SSSS manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 4 highlights
Cabinet dimensions/requirements typical installation tape ¹⁄₂" (12.7 mm) from front of countertop countertop moisture protection tape 19 50.5 cm) 3 9.7 cm) 2 6.7 cm) moisture protection tape Utility hole: 1¹⁄₂" (3.8 cm) dia. hole, either side - immediately adjacent to corner. 22⁷⁄₈" (58.0 cm) 23 60.0 cm) support surface must be solid and level 4" (10 cm) 16 41.2 cm) These marks indicate the side mounting tab screw locations. Minimum thickness of cabinet/cavity sides and bottom is 1.6 cm) ■ Build the custom cabinet to the size and specifications shown. The supporting base of the cabinet must be solid, level and able to sustain weight up to 104 lbs. (47 Kg), with a minimum thickness of cabinet/cavity sides and bottom of 1.6 cm). ■ A 3 prong grounded outlet must be installed within 6" (15.2 cm) to 18" (45.7 cm) to either side of the utility hole in the cabinet side wall. The power outlet must be accessible after installation. ■ It is recommended that wood cabinetry surrounding the dishwasher be sealed with an oil-based paint or moistureproof polyurethane to prevent possible damage from humidity. ■ A utility hole that will be used to route the power supply cord and hoses must be located as shown. If the hole is not located as shown, the hoses will prevent the dishwasher from being pushed back all the way into the cavity. Make sure the edges of the utility hole are smooth or covered. If the utility hole is through a metal cabinet, the hole must be protected with the edge protector provided. IMPORTANT: Custom wood door panel, if used, may be wider than the dishwasher to match surrounding cabinets. The 23⁵⁄₈" (60.0 cm) must be increased so that there is a 2.5 mm) clearance between the cabinet side and panel edge. Adjacent cabinetry must not extend above cavity base. Dishwasher 4 ■ For corner installation, there must be a ¹⁄₂" (12.7 mm) space between the adjacent cabinet doors (i.e. door knobs) and open dishwasher drawer. Water Supply Requirements For dishwasher: ■ Hot water line with 4.3-145 psi (30-1000 kPa) water pressure. ■ 120°F (48.8°C) water at dishwasher. ■ An easily accessible valve with 3/8" compression fitting must be installed in the hot water supply line. Electrical Requirements WARNING Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock. GROUNDING INSTRUCTIONS ■ The dishwasher must be grounded. In the event of a malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. The dishwasher is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is installed and grounded in accordance with all local codes and ordinances. WARNING: Improper connection of the equipment- grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service representative or personnel if you are in doubt as to whether the dishwasher is properly grounded. Do not modify the plug provided with the dishwasher: if it will not fit the outlet, have a proper outlet installed by a qualified electrician. SAVE THESE INSTRUCTIONS A 120-volt, 60 Hz, AC-only, 15 amp fused electrical supply is required. (Circuit breaker is recommended.) It is recommended that a separate circuit serving only this appliance be provided. Garbage Disposer: If you plan to install a garbage disposer, an additional separate 120-volt, 60 Hz, AC-only, 15 or 20 amp fused electrical supply is required.