Kyocera 9130DN Operation Guide - Page 59

Error Messages, disk.Wait until

Get Kyocera 9130DN - B/W Laser Printer PDF manuals and user guides View all Kyocera 9130DN manuals
Add to My Manuals
Save this manual to your list of manuals

Page 59 highlights

Troubleshooting Message Corrective Action Warning image adapt Printing job cannot be done in current resolution because there is not enough internal memory. Try adding more memory or changing resolution. Warning low memory The printer's internal memory is running low due to the number of fonts and macros downloaded. Print a status page to see how much user memory is left, and try deleting unnecessary fonts and macros. ;Ò:Alarm buzzer sounds when an error occurs. Press [CANCEL] to stop the alarm buzzer. Error Messages The following table lists error messages that can be dealt with by the user. Message File not found Press GO Corrective Action VMB: A VMB tray that was specified for output does not contain any jobs, or the VMB tray is not being used. Confirm the VMB tray. If Auto Continue is set to On, printing will be automatically resumed after a preset ;Òperiod of time. Format error Memory card This message appears when the printer is in the ready state and the memory card is not formatted, and therefore cannot be read or written. Format error Hard disk Initialization (formatting) of the hard disk is required. Initialize the hard disk. Hard disk err ## Look at the error code given in place of ## and refer to the corresponding Press GO description given below. 01: Hard disk format error. If this error recurs even if the power has been turned off and then on, reformat the hard disk. 02: The disk system is not installed. Recheck the requirements for using the system and the devices. 04: There is no available hard disk space. Delete unnecessary files, etc., to free up space. 05: The specified file does not exist in the hard disk. 06: There is no memory available to the hard disk system. Increase the available memory. 10: Formatting is not possible because host data is being spooled on the hard disk.Wait until Ready is displayed, and then format. 20: The hard disk was installed in the incorrect slot (OPT). Reinstall the hard disk in a different slot (HDD). 85: VMB; Alias error (the alias setting was lost, or the VMB tray corresponding to the alias does not exist). Set the alias again. 97: Code job; The number of permanent code jobs reached the limit value, and no more can be saved. Either delete some unnecessary jobs, etc., or increase the limit. ;Ò99: A print job for the specified ID does not exist in the hard disk. I/F occupied This message is displayed when you attempt to use the printer's operation panel to change the environmental settings on the interface from which data are presently being received. OPERATION GUIDE 4-11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
Troubleshooting
OPERATION GUIDE
4-11
Error Messages
The following table lists error messages that can be dealt with by the user.
Warning
image adapt
Printing job cannot be done in current resolution because there is not enough
internal memory. Try adding more memory or changing resolution.
Warning
low memory
The printer’s internal memory is running low due to the number of fonts and
macros downloaded. Print a status page to see how much user memory is left,
and try deleting unnecessary fonts and macros.
:
Alarm buzzer sounds when an error occurs. Press
[CANCEL]
to stop the alarm buzzer.
Message
Corrective Action
Message
Corrective Action
File not found
Press GO
VMB: A VMB tray that was specified for output does not contain any jobs, or the
VMB tray is not being used. Confirm the VMB tray.
If Auto Continue is set to
On
, printing will be automatically resumed after a preset
period of time.
Format error
Memory card
This message appears when the printer is in the ready state and the memory card
is not formatted, and therefore cannot be read or written.
Format error
Hard disk
Initialization (formatting) of the hard disk is required. Initialize the hard disk.
Hard disk err ##
Press GO
Look at the error code given in place of
##
and refer to the corresponding
description given below.
01:
Hard disk format error. If this error recurs even if the power has been turned
off and then on, reformat the hard disk.
02:
The disk system is not installed. Recheck the requirements for using the
system and the devices.
04:
There is no available hard disk space. Delete unnecessary files, etc., to free
up space.
05:
The specified file does not exist in the hard disk.
06:
There is no memory available to the hard disk system. Increase the
available memory.
10:
Formatting is not possible because host data is being spooled on the hard
disk.Wait until
Ready
is displayed, and then format.
20:
The hard disk was installed in the incorrect slot (OPT). Reinstall the hard
disk in a different slot (HDD).
85:
VMB; Alias error (the alias setting was lost, or the VMB tray corresponding
to the alias does not exist). Set the alias again.
97:
Code job; The number of permanent code jobs reached the limit value, and
no more can be saved. Either delete some unnecessary jobs, etc., or
increase the limit.
99:
A print job for the specified ID does not exist in the hard disk.
I/F occupied
This message is displayed when you attempt to use the printer’s operation panel
to change the environmental settings on the interface from which data are
presently being received.