Kyocera FS-C5200DN FS-C5100DN/C5200DN/C5300DN Operation Guide Rev-1.2 (Advance - Page 106

Password Administrator Password input, Change ID Administrator ID change

Get Kyocera FS-C5200DN PDF manuals and user guides View all Kyocera FS-C5200DN manuals
Add to My Manuals
Save this manual to your list of manuals

Page 106 highlights

Password _ >Change ID 00000001 >Change ID 001 >Change ID _ OK? 002 Password (Administrator Password input) You can use this to set the administrator password. The default setting is the numeric part of your printer's model name. If you use FS-C5300DN, enter "5300". 1 Once you have entered the correct ID in the previous step (ID (Administrator ID input)), the message display shows Password (Administrator password input) and a blinking cursor (_). 2 Press U or V to increase or decrease, respectively, the value at the blinking cursor. Enter the specified password. Use Y and Z to move the cursor right and left. Enter a password consisting of between 0 and 16 numbers. Note If you enter the incorrect administrator ID or password, the Wrong ID or Wrong Password message appears and the input screen then reappears. Re-enter the ID or password correctly. 3 Once you enter the correct ID and password, the Admin (change) screen appears. (E.g.: Where the administrator ID is 00000001) Each time you press U or V, the following settings to be changed appear in succession. • Change ID • Change Password Note If a change is required, refer to the procedures in Change ID (Administrator ID change) and Change Password (Administrator Password change) below. 4 Press [OK] again. The administrator ID and password are confirmed. 5 Press [MENU]. The display returns to Ready. Change ID (Administrator ID change) You can use this to change the administrator ID. 1 In step 3 in Password (Administrator Password input) above, press U or V while the Admin (Change) screen is displayed until >Change ID appears. (E.g.: Where the administrator ID is 001) 2 When you press [OK], a blinking cursor (_) appears. 3 Press U or V to increase or decrease, respectively, the value at the blinking cursor. Enter the ID to be changed. Use Y and Z to move the cursor right and left. Enter an ID consisting of between 1 and 16 numbers. 4 Press [OK]. A confirmation screen appears. (E.g.: Where the administrator ID is changed to 002) 5 Press [OK]. The new administrator ID is confirmed. 6 Press [MENU]. The display returns to Ready. 2-82 Using the Operation Panel

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
2-82
Using the Operation Panel
Password (Administrator Password input)
You can use this to set the administrator password. The default setting is
the numeric part of your printer's model name. If you use FS-C5300DN,
enter "
5300
".
1
Once you have entered the correct ID in the previous step (ID
(Administrator ID input)), the message display shows
Password
(Administrator password input) and a blinking cursor (
_
).
2
Press
U
or
V
to increase or decrease, respectively, the value at the
blinking cursor. Enter the specified password. Use
Y
and
Z
to move
the cursor right and left. Enter a password consisting of between 0
and 16 numbers.
3
Once you enter the correct ID and password, the
Admin (change)
screen appears. (E.g.: Where the administrator ID is
00000001
)
Each time you press
U
or
V
, the following settings to be changed
appear in succession.
•
Change ID
•
Change Password
4
Press
[OK]
again. The administrator ID and password are confirmed.
5
Press
[MENU]
. The display returns to
Ready
.
Change ID (Administrator ID change)
You can use this to change the administrator ID.
1
In step 3 in
Password (Administrator Password input)
above, press
U
or
V
while the
Admin (Change)
screen is displayed until
>Change
ID
appears. (E.g.: Where the administrator ID is
001
)
2
When you press
[OK]
, a blinking cursor (
_
) appears.
3
Press
U
or
V
to increase or decrease, respectively, the value at the
blinking cursor. Enter the ID to be changed. Use
Y
and
Z
to move the
cursor right and left. Enter an ID consisting of between 1 and 16
numbers.
4
Press
[OK]
. A confirmation screen appears. (E.g.: Where the
administrator ID is changed to
002
)
5
Press
[OK]
. The new administrator ID is confirmed.
6
Press
[MENU]
. The display returns to
Ready
.
Note
If you enter the incorrect administrator ID or password,
the
Wrong ID
or
Wrong Password
message appears and
the input screen then reappears. Re-enter the ID or password
correctly.
Note
If a change is required, refer to the procedures in
Change ID (Administrator ID change)
and
Change Password
(Administrator Password change)
below.
Password
_
>Change ID
00000001
>Change ID
001
>Change ID
_
OK?
002