LG KG6000R Owners Manual - Page 9

WindowRequirements

Get LG KG6000R PDF manuals and user guides View all LG KG6000R manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

WindowRequirements NOTE: All supporting parts should be secured to firm wood, masonry, or metal. 1. This unit is designed for installation in standard double hung windows with actual opening widths of 22" to 36" The upper and lower sash must open sufficiently to allow a clear vertical opening of 14" from the bottom of the sash to the window st_l. 2Jf storm window presents interference, fasten a 2" wide wood strip (OUTER SILL) to the inner window sill across the full width of the sill. The w_d strip should be thick enough to raise the height of the window sill so that the unit can be installed without interference by the storm window frame. See Rg. 5-2. Top d wood strip should be approximately 3/4" higher than the storm window frame (STORM WINDOW FRAME) or wood strip (OUTDOORS) to help condensation to drain properly to the outside. 3. install a se_nd wood strip (_proximate[y 6" long by 11iz"wide and same thickness as first strip} in the center of the outer sill flush against the back off the inner sill. This will raise the L bra_et as shown Fig, 5-2, 4. If the distance between STORM WINDOW FRAME and WOOD STRIP MOUNTED ON TOP OF INNER SiLL is more than 1", two of wood strip are not necessa_, INNER WOOD STRIP MOUNTED 1" MAX. Fig. 5-1 Fig. 5-2 HARDWARE [ TYPE A: 11 EA TYPE B: 5EA (SHORTSCREW) _ (WOOD SCREW) _ .E _ E TYPE D: lEA (SEAL STRIP) (Adhesive backed) TYPE E: lEA (SASH SEAL} (Notadhesivebacked) TYPE F: 2EA (GUIDE PANEL} TYPE C: 3EA (L BRACKET) TYPE G: lEA (SUPPORT BRACKET)

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
WindowRequirements
NOTE: All supporting parts should be secured to firm wood, masonry, or metal.
1. This
unit
is designed for installation in standard double hung windows with actual opening widths of
22" to 36"
The upper and lower sash must open sufficiently to allow a clear vertical opening of 14"
from the bottom of the sash to the window st_l.
2Jf storm window presents interference, fasten a 2" wide wood strip (OUTER SILL) to the inner
window sill across the full width of the sill. The w_d
strip should be thick enough to raise the height
of the window sill so that the unit can be installed without interference by the storm window frame.
See Rg. 5-2. Top
d
wood strip should be approximately
3/4" higher than the storm window frame
(STORM WINDOW
FRAME) or wood strip (OUTDOORS)
to help condensation to drain properly to
the outside.
3. install a se_nd
wood strip (_proximate[y
6" long by 11iz"wide and same thickness as first strip} in
the center of the outer sill flush against the back off the inner sill. This will raise the L bra_et
as
shown Fig, 5-2,
4. If the distance between STORM WINDOW FRAME and WOOD STRIP MOUNTED ON TOP OF
INNER SiLL is more than 1", two of wood strip are not necessa_,
INNER
WOOD STRIP MOUNTED
1" MAX.
Fig. 5-1
Fig. 5-2
HARDWARE
[
TYPE A: 11 EA
TYPE B: 5EA
TYPE C: 3EA
(SHORTSCREW)
_
(WOODSCREW)
_
(L BRACKET)
.
E
_
E
TYPE D: lEA
(SEALSTRIP)
(Adhesive backed)
TYPE E: lEA
(SASH SEAL}
(Notadhesivebacked)
TYPE F: 2EA
(GUIDE PANEL}
TYPE G: lEA
(SUPPORT BRACKET)