Lantronix EDS16PR EDS - User Guide - Page 138

CLI Configuration

Get Lantronix EDS16PR PDF manuals and user guides View all Lantronix EDS16PR manuals
Add to My Manuals
Save this manual to your list of manuals

Page 138 highlights

Figure 15-5 CLI Configuration 15: Advanced Settings 2. Enter or modify the following settings: Command Line Interface Configuration Settings Login Password Enable Level Password Quit Connect Line Inactivity Timeout Telnet State Telnet Port Telnet Max Sessions SSH State SSH Port SSH Max Sessions Table 15-6 CLI Configuration Description Enter the password for Telnet access. Enter the password for access to the Command Mode Enable level. There is no password by default. Enter a string to terminate a connect line session and resume the CLI. Type before any key the user must press when holding down the Ctrl key. An example of such a string is L. Set an Inactivity Timeout value so the CLI session will disconnect if no data is received after the designated time period. Default is 15 minutes. Enter a value of 0 to disable. Select Disabled to disable Telnet access. Telnet is enabled by default. Enter the Telnet port to use for Telnet access. The default is 23. Maximum number of simultaneous Telnet sessions. The default is 3 and the maximum is 10. Select Disabled to disable SSH access. SSH is enabled by default. Enter the SSH port to use for SSH access. The default is 22. Maximum number of simultaneous SSH sessions. The default is 3 and the maximum is 10. EDS User Guide 138

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
15: Advanced Settings
EDS User Guide
138
Figure 15-5
CLI Configuration
2.
Enter or modify the following settings:
Table 15-6
CLI Configuration
Command Line Interface
Configuration Settings
Description
Login Password
Enter the password for Telnet access.
Enable Level Password
Enter the password for access to the Command Mode Enable level.
There is no password by default.
Quit Connect Line
Enter a string to terminate a connect line session and resume the
CLI. Type
<control>
before any key the user must press when
holding down the
Ctrl
key. An example of such a string is
<control>L.
Inactivity Timeout
Set an Inactivity Timeout value so the CLI session will disconnect if
no data is received after the designated time period. Default is 15
minutes.
Enter
a value of 0 to disable.
Telnet State
Select
Disabled
to disable Telnet access. Telnet is enabled by
default.
Telnet Port
Enter the Telnet port to use for Telnet access. The default is
23
.
Telnet Max Sessions
Maximum number of simultaneous Telnet sessions.
The default is
3 and the maximum is 10.
SSH State
Select
Disabled
to disable SSH access. SSH is enabled by default.
SSH Port
Enter the SSH port to use for SSH access. The default is
22
.
SSH Max Sessions
Maximum number of simultaneous SSH sessions. The default is 3
and the maximum is 10.