Lantronix IntelliBox-I/O IntelliBox-I/O - Command Reference - Page 70

Applies Line Printer Daemon LPD protocol on the line., line 2 line:2 level commands

Get Lantronix IntelliBox-I/O PDF manuals and user guides View all Lantronix IntelliBox-I/O manuals
Add to My Manuals
Save this manual to your list of manuals

Page 70 highlights

line lpd name no clear line counters no command mode no command mode serial string no command mode signon message no name parity even parity none parity odd protocol lpd protocol lpd or tunnel protocol modbus ascii protocol modbus rtu protocol none protocol tunnel reassert show show command mode show history show line show statistics state disable state enable stop bits 1 stop bits 2 terminal terminal network termination disable termination enable tunnel write xoff char xon char line 2 (line:2) level commands auto show statistics baud rate clear line counters clrscrn command mode always IntelliBox-I/O 2100 Command Reference 5: Commands and Levels Enters the line level. Enters the configure lpd level. Sets the name for this line. Restores the serial counters to the aggregate values. Disables command mode for the current line. Prevents the user-defined serial boot string from being used to enter Clears the signon message displayed at boot time and when entering Removes the name of this line. Uses a parity bit on the line for even parity. Does not use a parity bit on the line. Uses a parity bit on the line for odd parity. Applies Line Printer Daemon (LPD) protocol on the line. Applies LPD or tunnel protocol on the line. Applies Modbus ASCII protocol on the line. Applies Modbus RTU protocol on the line. Uses no protocol on the line. Applies tunnel protocol on the line. Asserts line status with current configured values. Displays the current status. Shows the command mode settings for the current line. Displays the last 20 commands entered during the current CLI session. Displays the current configuration. Shows the line statistics. Disables the line so data cannot be sent/received. Enables the line so data can be sent/received. Uses one stop bit after data on the line. Uses two stop bits after data on the line. Enters the configure-terminal level. Enters the configure-terminal level for the network. Refrains from terminating the line. Enables 120 ohm line termination in RS485 half-duplex mode. Enters the tunnel level. Stores the current configuration in permanent memory. Sets the xoff character for use with software flow control on this line. Sets the xon character for use with software flow control on this line. Continuously displays line statistics. Sets the line speed. Sets the serial counters to zero. Clears the screen. Sets the current line to always be in command mode. 70

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
5: Commands and Levels
IntelliBox-I/O 2100 Command Reference
70
line
<line>
Enters the line level.
lpd
<line>
Enters the configure lpd level.
name
<text>
Sets the name for this line.
no clear line counters
Restores the serial counters to the aggregate values.
no command mode
Disables command mode for the current line.
no command mode serial string
Prevents the user-defined serial boot string from being
used to enter
no command mode signon message
Clears the signon message displayed at boot time and
when entering
no name
Removes the name of this line.
parity even
Uses a parity bit on the line for even parity.
parity none
Does not use a parity bit on the line.
parity odd
Uses a parity bit on the line for odd parity.
protocol lpd
Applies Line Printer Daemon (LPD) protocol on the line.
protocol lpd or tunnel
Applies LPD or tunnel protocol on the line.
protocol modbus ascii
Applies Modbus ASCII protocol on the line.
protocol modbus rtu
Applies Modbus RTU protocol on the line.
protocol none
Uses no protocol on the line.
protocol tunnel
Applies tunnel protocol on the line.
reassert
Asserts line status with current configured values.
show
Displays the current status.
show command mode
Shows the command mode settings for the current line.
show history
Displays the last 20 commands entered during the current
CLI session.
show line
Displays the current configuration.
show statistics
Shows the line statistics.
state disable
Disables the line so data cannot be sent/received.
state enable
Enables the line so data can be sent/received.
stop bits 1
Uses one stop bit after data on the line.
stop bits 2
Uses two stop bits after data on the line.
terminal
<line>
Enters the configure-terminal level.
terminal network
Enters the configure-terminal level for the network.
termination disable
Refrains from terminating the line.
termination enable
Enables 120 ohm line termination in RS485 half-duplex
mode.
tunnel
<line>
Enters the tunnel level.
write
Stores the current configuration in permanent memory.
xoff char
<control>
Sets the xoff character for use with software flow control
on this line.
xon char
<control>
Sets the xon character for use with software flow control
on this line.
line 2 (line:2) level commands
auto show statistics
Continuously displays line statistics.
baud rate
<bits per second>
Sets the line speed.
clear line counters
Sets the serial counters to zero.
clrscrn
Clears the screen.
command mode always
Sets the current line to always be in command mode.