Lenovo Horizon 27 Table PC IdeaCentre Horizon 27 All-In-One PC Hardware Mainte - Page 49

Replacing the solid state disk, Remove the rear cover. Refer to Removing the rear cover.

Get Lenovo Horizon 27 Table PC PDF manuals and user guides View all Lenovo Horizon 27 Table PC manuals
Add to My Manuals
Save this manual to your list of manuals

Page 49 highlights

Step 7. Step 8. Step 9. Remove the 2 screws that secure the TV-Tuner card to the motherboard. Disconnect the antenna cable(s) from the TV-Tuner card. Pull the TV-Tuner card upward to remove it from the card port. Step 10. To install the new TV-Tuner card: a. Insert the notched end of the TV-Tuner card into the card port. b. Secure the new TV-Tuner card to the motherboard with the 2 screws. c. Connect the antenna cable(s) to the new TV-Tuner card. d. Reconnect the battery cable to the connector on the motherboard. Step 11. Reattach the EMI and rear cover. Replacing the solid state disk Note: Turn off the computer and wait 3 to 5 minutes to let it cool down before removing the base cover. To replace the solid state disk: Step 1. Step 2. Step 3. Step 4. Step 5. Step 6. Remove any media (disks, CDs, DVDs, or memory cards) from the drives, shut down the operating system, and turn off the computer and all attached devices. Unplug all power cords from electrical outlets. Disconnect all cables attached to the computer. This includes power cords, input/output (I/O) cables, and any other cables that are connected to the computer. Refer to "Left and right view" and "Rear view" for help with locating the various connectors. Remove the rear cover. Refer to "Removing the rear cover". Remove the EMI cover. Refer to "Removing the EMI cover". Disconnect the battery cable from the connector on motherboard. Refer to "Replacing the battery". Chapter 8. Replacing hardware 43

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
Step 7.
Remove the 2 screws that secure the TV-Tuner card to the motherboard.
Step 8.
Disconnect the antenna cable(s) from the TV-Tuner card.
Step 9.
Pull the TV-Tuner card upward to remove it from the card port.
Step10. To install the new TV-Tuner card:
a.
Insert the notched end of the TV-Tuner card into the card port.
b.
Secure the new TV-Tuner card to the motherboard with the 2 screws.
c.
Connect the antenna cable(s) to the new TV-Tuner card.
d.
Reconnect the battery cable to the connector on the motherboard.
Step 11. Reattach the EMI and rear cover.
Replacing the solid state disk
Note:
Turn off the computer and wait 3 to 5 minutes to let it cool down before removing the base cover.
To replace the solid state disk:
Step 1.
Remove any media (disks, CDs, DVDs, or memory cards) from the drives, shut down the operating
system, and turn off the computer and all attached devices.
Step 2.
Unplug all power cords from electrical outlets.
Step 3.
Disconnect all cables attached to the computer. This includes power cords, input/output (I/O)
cables, and any other cables that are connected to the computer. Refer to “Left and right view”
and “Rear view” for help with locating the various connectors.
Step 4.
Remove the rear cover. Refer to “Removing the rear cover”.
Step 5.
Remove the EMI cover. Refer to “Removing the EMI cover”.
Step 6.
Disconnect the battery cable from the connector on motherboard. Refer to “Replacing the battery”.
Chapter 8
.
Replacing hardware
43