Lenovo ThinkStation E20 User Manual - Page 45

Replacing the rear fan assembly

Get Lenovo ThinkStation E20 PDF manuals and user guides View all Lenovo ThinkStation E20 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

Replacing the rear fan assembly Attention Do not open your computer or attempt any repair before reading and understanding the "Important safety information" in the ThinkStation Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkStation Safety and Warranty Guide, go to: http://www.lenovo.com/support This section provides instructions on how to replace the rear fan assembly. To replace the rear fan assembly, do the following: 1. Remove the computer cover. See "Removing the computer cover" on page 14. 2. Locate the rear fan assembly. See "Locating components" on page 10. 3. Disconnect the rear fan assembly cable from the system fan connector on the system board. See "Locating parts on the system board" on page 11. 4. The rear fan assembly is attached to the chassis by four rubber mounts. Remove the rear fan assembly by breaking or cutting the four rubber mounts and gently pulling the rear fan assembly out of the chassis. Figure 30. Removing the rear fan assembly 5. Install the new rear fan assembly by aligning the new rubber mounts with the corresponding holes in the chassis and push the rubber mounts through the holes. Note: The new rear fan assembly you received will have four new rubber mounts attached. Chapter 2. Installing or replacing hardware 37

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
Replacing the rear fan assembly
Attention
Do not open your computer or attempt any repair before reading and
understanding the “Important safety information” in the
ThinkStation Safety
and Warranty Guide
that came with your computer. To obtain a copy of the
ThinkStation Safety and Warranty Guide
, go to:
This section provides instructions on how to replace the rear fan assembly.
To replace the rear fan assembly, do the following:
1.
Remove the computer cover. See “Removing the computer cover” on page 14.
2.
Locate the rear fan assembly. See “Locating components” on page 10.
3.
Disconnect the rear fan assembly cable from the system fan connector on the
system board. See “Locating parts on the system board” on page 11.
4.
The rear fan assembly is attached to the chassis by four rubber mounts.
Remove the rear fan assembly by breaking or cutting the four rubber mounts
and gently pulling the rear fan assembly out of the chassis.
5.
Install the new rear fan assembly by aligning the new rubber mounts with the
corresponding holes in the chassis and push the rubber mounts through the
holes.
Note:
The new rear fan assembly you received will have four new rubber
mounts attached.
Figure 30. Removing the rear fan assembly
Chapter 2. Installing or replacing hardware
37