LevelOne FCS-1131 Manual

LevelOne FCS-1131 Manual

Get LevelOne FCS-1131 PDF manuals and user guides View all LevelOne FCS-1131 manuals
Add to My Manuals
Save this manual to your list of manuals

LevelOne FCS-1131 manual content summary:

  • LevelOne FCS-1131 | Manual - Page 1
    FCS-1131 2-Megapixel PoE Network Camera User Manual Ver 1.0 HW Ver: 2.0
  • LevelOne FCS-1131 | Manual - Page 2
    Table of Contents 1. Overview ...4 1.1 Features...5 1.2 Package Contents ...5 1.3 Dimensions...6 1.4 Connectors ...6 2. Camera Cabling ...7 2.1 Connect Power...7 2.2 Connect Ethernet Cable ...7 2.3 Connect Alarm I/O ...7 3. System Requirements ...8 4. Accessing Camera...9 4.1 Recording Software...14
  • LevelOne FCS-1131 | Manual - Page 3
    5.3.3.11 Network Failure Detection 55 5.3.3.12 Tampering ...57 5.3.3.13 Storage Management (Local Recording 61 5.3.3.14 Recording (Local Recording 63 5.3.3.15 File Location (Snapshots and Web Recording 64 5.3.3.16 Iris Adjustment (Fixed Focal Lens Excluded 65 5.3.3.17 View Information 66
  • LevelOne FCS-1131 | Manual - Page 4
    Default ID / Password Login ID root Password 3
  • LevelOne FCS-1131 | Manual - Page 5
    supports both H.264 and Motion JPEG. The camera has a built-in slot for an Mirco SD/SDHC card, enabling local storage of several days of recording, without any external equipment. The integrated BNC connector allows the FCS-1131 CH LevelOne IP CamSecure surveillance management software, the FCS-1131
  • LevelOne FCS-1131 | Manual - Page 6
    Vertical View Mode (Image rotation by 90 degrees) Smart IR Mode Network Failure Detection Day / Night (ICR) Auto Iris Lens support Micro SD support BNC Analog Output ONVIF Support 1.2 Package Contents  FCS-1131  Power Adapter  Camera Stand  Quick Installation Guide  CD Manual / Utility 5
  • LevelOne FCS-1131 | Manual - Page 7
    1.3 Dimensions 1.4 Connectors The diagram below shows the IP Camera's reset button and various connectors. Definition for each connector will be given as follows. No. Definition 1 LINE OUT & LINE IN 2 Power LED 3 Reset Button 4 AUTO IRIS connector 5 NETWORK (with PoE) 6 NETWORK LEDs 7 Alarm I/O 8
  • LevelOne FCS-1131 | Manual - Page 8
    2. Camera Cabling Please follow the instructions below to complete IP Camera installation. 2.1 Connect Power Please refer to Section: Connectors. Alternatively, connect the Ethernet cable to the camera's PoE port and plug
  • LevelOne FCS-1131 | Manual - Page 9
    3. System Requirements To perform the IP Camera via web browser, please ensure your PC is in good network connection, and meet system requirements as described below. Items Personal Computer Operating System Web Browser Network Card Viewer System Requirement 1. Intel® Pentium® M, 2.16 GHz or Intel
  • LevelOne FCS-1131 | Manual - Page 10
    4. Accessing Camera For initial access to the IP Camera, users can search the camera through the installer program: DeviceSearch.exe, which can be found in "DeviceSearch" folder in the supplied CD. Device Search Software Step 1: Double click on the program Device Search.exe (see the icon below); its
  • LevelOne FCS-1131 | Manual - Page 11
    Step 3: Click "Device Search" again, and all the finding IP devices will be listed in the page, as shown in the figure below. The IP Camera's default IP address is: 192.168.0.250. Step 4: Double click or right click and select "Browse" to access the camera directly via web browser. Step 5: Then the
  • LevelOne FCS-1131 | Manual - Page 12
    The default login ID and password for the Administrator are: Login ID root Password NOTE: ID and password are case sensitive. NOTE: It is strongly advised that administrator's password be altered for the security concerns. Additionally, users can change the IP Camera's network property, either
  • LevelOne FCS-1131 | Manual - Page 13
    Step 3: Click "OK" on the Note of setting change. Wait for one minute to re-search the IP Camera. Step 4: Click the "Device Search" button to re-search all the devices. Then select the IP Camera with the correct MAC address. Double click on the IP Camera, and the login window will appear. Step 5:
  • LevelOne FCS-1131 | Manual - Page 14
    13
  • LevelOne FCS-1131 | Manual - Page 15
    the program to add the Network Camera to the Channel list. For detailed information about how to use IP CamSecure, please refer to the user's manual of the software or download it at http://global.level1.com. 14
  • LevelOne FCS-1131 | Manual - Page 16
    4.2 Installing DC Viewer Software Online For the initial access to the IP Camera, a client program, DC Viewer, will be automatically installed to your PC when connecting to the IP Camera. If the Web browser doesn't allow DC Viewer installation, please check the Internet security settings or ActiveX
  • LevelOne FCS-1131 | Manual - Page 17
    Once login to the IP Camera, users will see the Home page as shown below: 16
  • LevelOne FCS-1131 | Manual - Page 18
    5. Operation & Configuration The IP Camera is provided with a user-friendly browser-based configuration interface for video playback and recording. In this chapter, information about main page introduction, system related settings and camera settings will be described in detail. 5.1 Browser-based
  • LevelOne FCS-1131 | Manual - Page 19
    System setting The administrator can set host name, system time, root password, network related settings, etc. Further details will be interpreted in chapter System. Streaming setting The administrator can modify video resolution and rotate type and select audio compression mode in this page. Camera
  • LevelOne FCS-1131 | Manual - Page 20
    information of each item is as described in the following chapter. 5.2.1 Function Items on Home Page Multiple Languages Support Multiple languages are supported, including German, English, French, Italian, Simplified Chinese, Traditional Chinese, Russian for the viewer window interface. Digital Zoom
  • LevelOne FCS-1131 | Manual - Page 21
    Screen Size Adjustment Image display size can be adjusted to x1/2 and full screen. Talk button (on/off) Talk function allows the local site to talk to the remote site. Click on the button to switch it to on/off. Please refer to Security: Add user > Talk/Listen for further details. This function is
  • LevelOne FCS-1131 | Manual - Page 22
    5.3 System Under the tab , there are submenus including: , , , , , , , , , , , , , , , , <
  • LevelOne FCS-1131 | Manual - Page 23
    field. Sync With Computer Time Select the item, and video date and time display will synchronize with the PC's. Manual The Administrator can set video date, time and day manually. Entry format should be identical with that shown next to the enter fields. Sync with NTP server Network Time Protocol
  • LevelOne FCS-1131 | Manual - Page 24
    5.3.2 Security The Security setting can be found under this path: System> Security. Click on the Security category, there will be a drop-down menu with tabs including , , , and . 5.3.2.1 User The User setting can be found under this path: System> Security> User.
  • LevelOne FCS-1131 | Manual - Page 25
    is a maximum of twenty user accounts. Each user can be assigned the privileges of "Camera control", "Talk" and "Listen".  I/O access This item supports fundamental functions that enable users to view video when accessing to the camera.  Camera control This item allows the appointed User to change
  • LevelOne FCS-1131 | Manual - Page 26
    5.3.2.2 HTTPS The HTTPS setting can be found under this path: System> Security> HTTPS. allows secure connections between the IP Camera and web browser using or , which ensure camera settings or Username/ Password info from snooping.
  • LevelOne FCS-1131 | Manual - Page 27
    Click on button under "Create self-signed certificate" and provide the requested information to install a self-signed certificate for the IP Camera. Please refer to the last part of this section: Provide the Certificate Information for more details. NOTE: The self-signed certificate does
  • LevelOne FCS-1131 | Manual - Page 28
     State or province Enter the local administrative region.  Locality Enter other geographical information.  Organization Enter the name of the organization to which the entity identified in"Common Name" belongs.  Organization Unit Enter the name of the organizational unit to which the entity
  • LevelOne FCS-1131 | Manual - Page 29
    5.3.2.3 IP Filter The IP Filter setting can be found under this path: System> Security> IP Filter. Using the IP filter, access to the IP Camera can be restricted by denying/allowing specific IP addresses.  Enable IP Filter Check the box to enable the IP Filter function. Once enabled, the listed IP
  • LevelOne FCS-1131 | Manual - Page 30
    The Filtered IP Addresses list box shows the currently configured IP addresses. Up to 256 IP address entries may be specified. To remove an IP address from the list, please select the IP and then click on the button. 5.3.2.4 IEEE 802.1X The IEEE 802.1X setting can be found under this path:
  • LevelOne FCS-1131 | Manual - Page 31
    Client Certificate/ Private Key Upload the Client Certificate and Private Key for authenticating the IP Camera itself. Settings  Identity Enter the user identity associated with the certificate. Up to 16 characters can be used.  Private Key Password Enter the password (maximum 16 characters) for
  • LevelOne FCS-1131 | Manual - Page 32
    : System> Network> Basic. Users can choose to connect to the IP Camera with fixed or dynamic (DHCP) IP address. The IP Camera also provides PPPoE support for users who connect to the network via PPP over Ethernet (PPPoE). 31
  • LevelOne FCS-1131 | Manual - Page 33
    General  Get IP address automatically (DHCP) The camera's default setting is . If select , after the IP Camera restarts, users can search it through the installer program: DeviceSearch.exe, which can be found in "DeviceSearch" folder in the
  • LevelOne FCS-1131 | Manual - Page 34
    1024 to 65535. NOTE: Be aware to choose the different port from the one set for the web server port. IPv6 Address Configuration With IPv6 support, users can use the corresponding IPv6 address for browsing. Enable IPv6 by checking the box and click on to complete the setting. 33
  • LevelOne FCS-1131 | Manual - Page 35
    for different types of traffic packets, which guarantees delivery of priority services especially when network congestion occurs. Adapting the Differentiated Services (DiffServ) model, traffic flows are classified and marked with DSCP (DiffServ Codepoint) values, and thus receive the corresponding
  • LevelOne FCS-1131 | Manual - Page 36
    The class consists of HTTP traffic: Web browsing. NOTE: To enable this function, please make sure the switches/ routers in the network support QoS. 5.3.3.3 SNMP The SNMP (Simple Network Management Protocol) setting can be found under this path: System> Network> SNMP. With Simple Network Management
  • LevelOne FCS-1131 | Manual - Page 37
    community name that has read-only access to all supported SNMP objects. The default value is "public".  Write Community Specify the community name that has read/write access to all supported SNMP objects (except read-only objects). The default value is "write".
  • LevelOne FCS-1131 | Manual - Page 38
    5.3.3.4 UPnP The UPnP setting can be found under this path: System> Network> UPnP. UPnP Setting  Enable UPnP When the UPnP is enabled, whenever the IP Camera is presented to the LAN, the icon of the connected IP Cameras will appear in My Network Places to allow for direct access. NOTE: To enable
  • LevelOne FCS-1131 | Manual - Page 39
    IP Camera is allowed to open the web server port on the router automatically. NOTE: To enable this function, please make sure that your router supports UPnP and it is activated.  Friendly name Set the name for the IP Camera for identity. 38
  • LevelOne FCS-1131 | Manual - Page 40
    5.3.3.5 DDNS The DDNS setting can be found under this path: System> DDNS. Dynamic Domain Name System (DDNS) allows a host name to be constantly synchronized with a dynamic IP address. In other words, it allows those using a dynamic IP address to be associated to a static domain name so others can
  • LevelOne FCS-1131 | Manual - Page 41
    Username/E-mail Enter the username or e-mail required by the DDNS provider for authentication. Password/Key Enter the password or key required by the DDNS provider for authentication. 40
  • LevelOne FCS-1131 | Manual - Page 42
    Port, Account Name, Password and E-mail Address settings. Check the box "SMTP SSL" to send emails via encrypted transmission. For SMTP server, contact your network service provider for more specific information. 41
  • LevelOne FCS-1131 | Manual - Page 43
    5.3.3.7 FTP The FTP setting can be found under this path: System> FTP. The Administrator can set as sending alarm message to a specific File Transfer Protocol (FTP) site when event is triggered. Users can assign alarm message to up to two FTP sites. Enter the FTP details, which include server,
  • LevelOne FCS-1131 | Manual - Page 44
    5.3.3.8 HTTP The HTTP setting can be found under this path: System> HTTP. A HTTP Notification server can listen for notification messages from IP Cameras by triggered events. Enter the HTTP details, which include server name (for instance, http://192.168.0.1/admin.php), user name, and password in
  • LevelOne FCS-1131 | Manual - Page 45
    ' images. Refer to alarm pin definition below to connect alarm devices to the IP Camera if needed. Alarm Pin Definition Please refer to User's Manual for Alarm Pin Definition to connect the alarm devices. Alarm Switch The Administrator can enable or disable the alarm function. Alarm Type Select an
  • LevelOne FCS-1131 | Manual - Page 46
    Alarm Output Define alarm output signal or as the normal alarm output status according to the current alarm application. Triggered Action (Multi-option) The Administrator can specify alarm actions that will take when the alarm is triggered. All options are listed as follows:  Enable
  • LevelOne FCS-1131 | Manual - Page 47
    trigger active until the alarm is released. Set the Image frequency as the upload frame rate. The setting range is from 1 frame to 15 frames. NOTE: Make sure FTP configuration has been completed. Refer to FTP for further details.  Upload Image by E-Mail Select this item and the Administrator can
  • LevelOne FCS-1131 | Manual - Page 48
    Pre-trigger buffer recording function allows users to check what happened to cause the trigger. The pre-trigger buffer time range is from 1 to 3 seconds. Select to set the recording duration after alarm is triggered. The setting range is from 1 to 99999 seconds. Select
  • LevelOne FCS-1131 | Manual - Page 49
    Save After complete all the settings mentions above, please click on button to save all the settings in this page. 48
  • LevelOne FCS-1131 | Manual - Page 50
    5.3.3.10 Motion Detection The Motion Detection setting can be found under this path: System> Motion Detection. Motion Detection function allows detecting suspicious motion and triggering alarms when motion volume in the detected area reaches/exceeds the determined sensitivity threshold value. In the
  • LevelOne FCS-1131 | Manual - Page 51
    Up 10 Motion Detection Windows can be set. Click on the button under the Live Video Pane to add a Motion Detection Window. To cancel a Motion Detection Window, move the mouse cursor to the selected Window, and click on the button. If Motion Detection function is activated, the pop-off
  • LevelOne FCS-1131 | Manual - Page 52
     Sampling pixel interval [1-10]: The default value is 1. If the value is set as 3, it means within the detection region, system will take one sampling pixel for every 3 pixels by each row and each column (refer to the figure below).  Detection level [1-100]: The default level is 10. The item is to
  • LevelOne FCS-1131 | Manual - Page 53
    Select to set the recording duration after motion event occurs. The setting range is from 1 to 99999 seconds. Select to record the triggered video until the trigger is off. NOTE: Please make sure the local recording (with Micro SD/SDHC card) is
  • LevelOne FCS-1131 | Manual - Page 54
    various parameters. When motion is detected, event images will be sent to the appointed e-mail address. function allows users to check what happened to cause the trigger. The frame rate could be pre-determined. On the other hand, is for
  • LevelOne FCS-1131 | Manual - Page 55
     Add sequence number suffix (no maximum value) File name: imageXXXXXXX.jpg X: Sequence Number  Add sequence number suffix up to # and then start over File Name: imageXX.jpg X: Sequence Number The file name suffix will end at the number being set. For example, if the setting is up to "10," the file
  • LevelOne FCS-1131 | Manual - Page 56
    5.3.3.11 Network Failure Detection Ne twork Failure Detection allows the IP Camera to ping another IP device (e.g. NVR, VSS, Video Server, etc.) within the network periodically and generates some actions in case of network failure occurs, for instance, a Video Server is somehow disconnected. Being
  • LevelOne FCS-1131 | Manual - Page 57
    Triggered Action (Multi-option) The Administrator can specify alarm actions that will take when network failure is detected. All options are listed as follows:  Enable Alarm Output Select the item to enable alarm relay output.  Record Stream to SD Card Select the item and the alarm-triggered
  • LevelOne FCS-1131 | Manual - Page 58
    5.3.3.12 Tampering The Tampering setting can be found under this path: System> Tampering. Tampering Alarm function helps the IP Camera against tampering such as deliberate redirection, blocking, paint spray, and lens cover, etc through video analysis and reaction to such events by sending out
  • LevelOne FCS-1131 | Manual - Page 59
    Tampering Duration Minimum Tampering Duration is the time for video analysis to determine whether camera tampering has occurred. Minimum Duration could also be interpreted as defining the Tampering threshold; longer duration represents higher threshold. Settable Tampering Duration time range is from
  • LevelOne FCS-1131 | Manual - Page 60
    appointed FTP site. function allows users to check what happened to cause the trigger. The frame rate could be pre-determined. On the other hand, is for users to upload certain amount of images after tampering is triggered. Check the
  • LevelOne FCS-1131 | Manual - Page 61
    NOTE: Make sure SMTP configuration has been completed. Refer to Mail for further details.  Send HTTP notification Check this item, select the destination HTTP address, and specify the parameters for HTTP notifications. When the Tampering Alarm is triggered, the HTTP notifications can be sent to the
  • LevelOne FCS-1131 | Manual - Page 62
    5.3.3.13 Storage Management (Local Recording) The Storage Management setting can be found under this path: System> Storage Management. Users can implement local recording to the Micro SD/SDHC card up to 32GB. This page shows the capacity information of the Micro SD card and a recording list with all
  • LevelOne FCS-1131 | Manual - Page 63
    Device information When users insert the Micro SD/SDHC card, the card information such as the memory capacity and status will be shown at Device Information section. For the memory card being successfully installed, its status shall be shown at section in the Storage Management
  • LevelOne FCS-1131 | Manual - Page 64
    Recording) The Recording setting can be found under this path: System> Recording. In the Recording setting page, the Micro SD Card recording schedule supports up to ten sets of time frames. User can specify the recording schedule to fit the present surveillance requirement. Activating Micro SD/SDHC
  • LevelOne FCS-1131 | Manual - Page 65
    5.3.3.15 File Location (Snapshots and Web Recording) The File Location setting can be found under this path: System> File Location. Users can specify a storage location on the PC or in the hard drive for the snapshots and live video recording. The default setting is: C:\. Once confirm the setting,
  • LevelOne FCS-1131 | Manual - Page 66
    5.3.3.16 Iris Adjustment (Fixed Focal Lens Excluded) The Iris Adjustment function can be found under this path: System> Iris Adjustment. For users who use Auto-iris lens, when it is required to implement iris adjustment, please refer to the Iris adjustment procedure in the setting page to adjust
  • LevelOne FCS-1131 | Manual - Page 67
    5.3.3.17 View Information The View Information function can be found under this path: System> View Information. Click on the category: , there will be a drop-down menu with tabs including , , and . 5.3.3.17.1 Log File The Log File function
  • LevelOne FCS-1131 | Manual - Page 68
    5.3.3.17.2 User Information The User Information function can be found under this path: System> User Information. The Administrator can view each added user's login information and privileges (refer to Security). Get User Information All the users in the network will be listed in the
  • LevelOne FCS-1131 | Manual - Page 69
    5.3.3.17.3 Parameters .The Parameters function can be found under this path: System> Parameter. Click on this item to view the entire system's parameter setting such as Camera Settings, Mask Information and Network Information. 68
  • LevelOne FCS-1131 | Manual - Page 70
    5.3.3.18 Factory Default The Factory Default setting can be found under this path: System> Factory Default. Users can follow the instructions on this page to reset the IP Camera to factory default setting if needed. Set Default Click on the button to recall the
  • LevelOne FCS-1131 | Manual - Page 71
    5.3.3.19 Software Version The Software Version can be found under this path: System> Software Version. The current software version is displayed in the software version page. 70
  • LevelOne FCS-1131 | Manual - Page 72
    5.3.3.20 Software Upgrade The Software Upgrade setting can be found under this path: System> Software Upgrade. NOTE: Make sure the upgrade software file is available before carrying out software upgrade. The procedure of software upgrade is as below: Step 1. Click on "Browse" and select the binary
  • LevelOne FCS-1131 | Manual - Page 73
    exists or not first, and then begin to upload the upgrade file. Subsequently, the upgrade status bar will display on the page. When it runs to 100%, the upgrade process is finished. After the upgrade process is finished, the viewer will return to Home page. Step 4. Close the video browser. Step 5.
  • LevelOne FCS-1131 | Manual - Page 74
    5.3.3.21 Maintenance The Maintenance setting can be found under this path: System> Maintenance. Users can export configuration files to a specified location and retrieve data by uploading an existing configuration file to the IP Camera. Export Users can save the system settings by exporting the
  • LevelOne FCS-1131 | Manual - Page 75
    path: Streaming> Video Format. Video Resolution Under Video Resolution section, the available video resolution formats are including MJPEG and H.264. Please refer to the User's Manual for more combination details. Click on to confirm the setting. 74
  • LevelOne FCS-1131 | Manual - Page 76
    Text Overlay Settings Users can select the items to display data including date/time/text on the live video panel. The maximum length of the string is 20 alphanumeric characters. Click on to confirm the Text Overlay setting. Video Rotate Type Users can change video display type if necessary.
  • LevelOne FCS-1131 | Manual - Page 77
    NOTE: Please make sure the higher compression ratio is supported by system before setup. 5.4.2 Video Compression The Video Compression setting can be found under this path: Streaming> Video Compression. Users can select a proper MJPEG/H.264
  • LevelOne FCS-1131 | Manual - Page 78
    Display Compression Information Users can also decide whether to display compression information on the Home page. CBR Mode Setting The CBR (Constant Bit Rate) mode could be the preferred bit rate mode if the bandwidth available is limited. It is important to take account of image quality while
  • LevelOne FCS-1131 | Manual - Page 79
    5.4.3 Video ROI The Video ROI setting can be found under this path: Streaming> Video ROI. ROI stands for Region of Interest. This function allows users to select specific monitoring region for 2nd, 3rd and 4th streams, instead of showing the full image. NOTE: This function is only available when
  • LevelOne FCS-1131 | Manual - Page 80
     Enable Stream 3 ROI Setting Check the box and Stream 3 ROI Window will be displayed. To change the size of Stream 3 ROI Window, move the mouse cursor to the edge of the frame and draw it outward/inward. Moving the mouse to the center of the frame can shift the frame to the intended location. 
  • LevelOne FCS-1131 | Manual - Page 81
    5.4.4 Video OCX Protocol The Video OCX Protocol setting can be found under this path: Streaming> Video OCX Protocol. In the Video OCX protocol setting page, users can select RTP over UDP, RTP over RTSP (TCP), RTSP over HTTP or MJPEG over HTTP for streaming video over the network. In the case of
  • LevelOne FCS-1131 | Manual - Page 82
    5.4.5 Video Frame Rate The Video Frame Rate setting can be found under this path: Streaming> Video Frame Rate. Video frame rate is for setting the frames per second (fps) if necessary. MJPEG/ H.264-1/ H.264-2/ H.264-3/ H.264-4 Frame Rate The default setting of MJPEG/H.264-1/H.264-2/ H.264-3/ H.264-4
  • LevelOne FCS-1131 | Manual - Page 83
    5.4.6 Video Mask The Video Mask setting can be found under this path: Streaming> Video Mask. Active Mask Function  Add a Mask Check a Video Mask checkbox, and a red frame will come out in the Live Video panel at the right side. Use the mouse to drag and drop to adjust the mask's size and place it
  • LevelOne FCS-1131 | Manual - Page 84
    Mask Setting  Mask color The selections of Mask color include red, black, white, yellow, green, blue, cyan, and magenta. Click on to confirm the setting. 83
  • LevelOne FCS-1131 | Manual - Page 85
    5.4.7 Audio (Audio Mode and Bit Rate Settings) The Audio Mode setting can be found under this path: Streaming> Audio. In the Audio page, the Administrator can select one transmission mode and audio bit rate. Transmission Mode  Full-duplex (Talk and Listen simultaneously) In the Full-duplex mode,
  • LevelOne FCS-1131 | Manual - Page 86
     Simplex (Listen only) In the Listen only Simplex mode, the local/remote site can only listen to the other site.  Disable Select the item to turn off the audio transmission function. Server Gain Setting Set the audio input/output gain levels for sound amplification. The audio gain values are
  • LevelOne FCS-1131 | Manual - Page 87
    5.5 Camera Under the tab , there are submenus including: , , , , , , , , and . 86
  • LevelOne FCS-1131 | Manual - Page 88
    5.5.1 Exposure Setting The Exposure Setting can be found under this path: Camera> Exposure. The exposure is the amount of light received by the image sensor and is determined by the width of lens diaphragm opening, the amount of exposure by the sensor (shutter speed) and other exposure parameters.
  • LevelOne FCS-1131 | Manual - Page 89
    Manual Mode  Fixed Shutter Mode In this mode, fixed shutter speed could be selected from the dropdown menu. The shutter speed range is from 1/10000 to 1 (1/1.5) sec. with 19 (18) options. Users could select suitable shutter speed according to the environmental illumination. 88
  • LevelOne FCS-1131 | Manual - Page 90
    Mode is suitable for environment with light source having color temperature in the range roughly from 2500 ~ 10000K. Manual Mode In this mode, users can change the White Balance value manually. Users can select a number between 0 ~127 of "Rgain/ Bgain" item to gain the red/ blue illuminant on the
  • LevelOne FCS-1131 | Manual - Page 91
    5.5.3 Picture Adjustment The Picture Adjustment can be found under this path: Camera> Picture Adjustment. Brightness Users can adjust the image's brightness by adjusting the item. Please select ranging from -12 to +13. To increase video brightness, select a bigger number. Click on to confirm
  • LevelOne FCS-1131 | Manual - Page 92
    5.3.4 Backlight The Backlight Setting can be found under this path: Camera> Backlight. The Backlight Compensation function prevents the center object from being too dark in surroundings where excessive light is behind the center object. Click on < √ > to confirm the new setting. 5.3.5 Digital Zoom
  • LevelOne FCS-1131 | Manual - Page 93
    5.3.8 Noise Reduction The Noise Reduction Setting can be found under this path: Camera> Noise Reduction. The IP Camera provides multiple options for delivering optimized image quality especially in extra low-light conditions. Different level options for 3D Noise Reduction (3DNR)
  • LevelOne FCS-1131 | Manual - Page 94
    93
  • LevelOne FCS-1131 | Manual - Page 95
    Compression Video Streaming FCS-1131-V2 1/2.7" Progressive CMOS 1920(H) x 1080(V) 0.2 lux (Color) 0.02 lux (B/W) Manual / AWB/ ATW / Off Brightness Manual Exposure Auto / Manual Sharpness Manual Contrast Manual Saturation Manual Hue Manual Digital Zoom Support Motion Detection On
  • LevelOne FCS-1131 | Manual - Page 96
    ONVIF HTTPS / IP Filter / IEEE 802.1x 1 Set 5V 10kΩ pull up 1 Set Photo Relay Output 300V DC/AC HTTP / FTP / SMTP microSDHC 32GB support Internet Explorer (6.0+) / Chrome / Firefox / Safari 20 User and Administrator C / CS Mount Power / Link / ACT DC Drive 4 Pin Terminal Block, Pitch 3.5 mm DC jack
  • LevelOne FCS-1131 | Manual - Page 97
    Appendix B: Internet Security Settings If ActiveX control installation is blocked, please either set Internet security level to default or change ActiveX controls and plug-ins settings. Internet Security Level: Default Step 1: Start the Internet Explorer (IE). Step 2: Select from the main
  • LevelOne FCS-1131 | Manual - Page 98
    Step 4: Down the page, press "Default Level" (see the figure above) and click "OK" to confirm the setting. Close the browser window, and open a new one later when accessing the IP Camera. ActiveX Controls and Plug-ins Settings Step 1~3: Refer to the previous section above. Step 4: Down the page,
  • LevelOne FCS-1131 | Manual - Page 99
    The Security Settings screen is displayed as below: Step 5: Under "ActiveX controls and plug-ins", set ALL items (as listed below) to or . ActiveX controls and plug-in settings: 1. Automatic prompting for ActiveX controls 2. Binary and scrip behaviors 3. Download signed ActiveX
  • LevelOne FCS-1131 | Manual - Page 100
    Appendix C: DC Viewer Download Procedure The procedure of DC Viewer software download is specified as follows. Step 1: In the DC Viewer installation page, click "Next" for starting installing. Step 2: Setup starts. Please wait for a while until the loading bar runs out. 99
  • LevelOne FCS-1131 | Manual - Page 101
    Step 3: Click "Finish" to close the DC Viewer installation page. Then, the IP Camera's Home page will display as follows: 100
  • LevelOne FCS-1131 | Manual - Page 102
    Appendix D: Install UPnP Components Please follow the instructions below to install UPnP components. Step 1: Go to "Start", click on "Control Panel", and then double click "Add or Remove Programs". Step 2: Click on "Add/Remove Windows Components" in the Add or Remove Programs page.. 101
  • LevelOne FCS-1131 | Manual - Page 103
    Step 3: Select "Networking Services" from the Components list in the Windows Components Wizard window, and then click "Details". Step 4: Select "UPnP User Interface" in the Networking Services' subcomponents list and then click "OK". 102
  • LevelOne FCS-1131 | Manual - Page 104
    Step 5: Click "Next" in the Windows Components Wizard page. Step 6: Click "Finish" to complete installation. 103
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
FCS-1131
2-Megapixel PoE Network Camera
User Manual
Ver 1.0
HW Ver: 2.0