LevelOne FCS-1131 Manual - Page 60

Upload Image by E-Mail

Get LevelOne FCS-1131 PDF manuals and user guides View all LevelOne FCS-1131 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 60 highlights

appointed FTP site. function allows users to check what happened to cause the trigger. The frame rate could be pre-determined. On the other hand, is for users to upload certain amount of images after tampering is triggered. Check the box to upload the triggered images during certain time or keep uploading until the trigger is off. Select and enter the duration in the blank. The images of the duration will be uploaded to FTP when tampering is triggered. The setting range is from 1 to 9999 seconds. Select to make the images keep being upload to FTP during the trigger active until the tampering stops. Set the Image frequency as the upload frame rate. The setting range is from 1 frame to 15 frames. NOTE: Make sure FTP configuration has been completed. Refer to FTP for further details.  Upload Image by E-Mail Select this item and the Administrator can assign an e-mail address and configure various parameters. When tampering is detected, event images will be sent to the appointed e-mail address. function allows users to check what happened to cause the trigger. The frame rate could be pre-determined. On the other hand, is for users to upload certain amount of images after tampering occurs. Check the box to upload the triggered images during certain time or keep uploading until the trigger is off. Select and enter the duration in the blank. The images of the duration will be uploading by E-mail when tampering is triggered. The setting range is from 1 to 9999 seconds. Select to make the images keep being upload to E-mail during the trigger active until tampering stops. Set the Image frequency as the upload frame rate. The setting range is from 1 frame to 20 frames. 59

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
59
appointed FTP site.
<Pre-trigger buffer> function allows users to check what happened to cause the trigger.
The <Pre-trigger buffer> frame rate could be pre-determined.
On the other hand, <Post-trigger buffer> is for users to upload certain amount of images
after tampering is triggered.
Check the box <Continue image upload> to upload the triggered images during certain
time or keep uploading until the trigger is off. Select <Upload for __sec> and enter the
duration in the blank. The images of the duration will be uploaded to FTP when
tampering is triggered. The setting range is from 1 to 9999 seconds. Select <Upload
during the trigger active> to make the images keep being upload to FTP during the
trigger active until the tampering stops. Set the Image frequency as the upload frame
rate. The setting range is from 1 frame to 15 frames.
NOTE:
Make sure FTP configuration has been completed. Refer to FTP
for further details.
Upload Image by E-Mail
Select this item and the Administrator can assign an e-mail address and configure
various parameters. When tampering is detected, event images will be sent to the
appointed e-mail address.
<Pre-trigger buffer> function allows users to check what happened to cause the trigger.
The <Pre-trigger buffer> frame rate could be pre-determined.
On the other hand, <Post-trigger buffer> is for users to upload certain amount of images
after tampering occurs.
Check the box <Continue image upload> to upload the triggered images during certain
time or keep uploading until the trigger is off. Select <Upload for __sec> and enter the
duration in the blank. The images of the duration will be uploading by E-mail when
tampering is triggered. The setting range is from 1 to 9999 seconds. Select <Upload
during the trigger active> to make the images keep being upload to E-mail during the
trigger active until tampering stops. Set the Image frequency as the upload frame rate.
The setting range is from 1 frame to 20 frames.