LevelOne FCS-1131 Manual - Page 46

Alarm Output, Triggered Action Multi-option, Enable Alarm Output, IR Cut Filter, Send Message by FTP

Get LevelOne FCS-1131 PDF manuals and user guides View all LevelOne FCS-1131 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

Alarm Output Define alarm output signal or as the normal alarm output status according to the current alarm application. Triggered Action (Multi-option) The Administrator can specify alarm actions that will take when the alarm is triggered. All options are listed as follows:  Enable Alarm Output Select the item to enable alarm relay output.  IR Cut Filter Select the item and the camera's IR cut filter (ICR) will be removed (on) or blocked (off) when alarm input is triggered. Note: The IR Function (Refer to IR Function) could not be set as mode if this triggered action is enabled.  Send Message by FTP/E-Mail The Administrator can select whether to send an alarm message by FTP and/or E-Mail when an alarm is triggered.  Upload Image by FTP Select this item and the Administrator can assign a FTP site and configure various parameters. When the alarm is triggered, event images will be uploaded to the appointed FTP site. function allows users to check what happened to cause the trigger. The frame rate could be pre-determined. On the other hand, is for users to upload certain amount of images after the alarm input is triggered. Check the box to upload the triggered images during certain time or keep uploading until the trigger is off. Select and enter the duration in the blank. The images of the duration will be uploaded to FTP when the alarm input is triggered. The setting range is from 1 to 9999 seconds. Select to make the images keep being uploaded to FTP during the 45

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
45
Alarm Output
Define alarm output signal <high> or <low> as the normal alarm output status according to
the current alarm application.
Triggered Action (Multi-option)
The Administrator can specify alarm actions that will take when the alarm is triggered. All
options are listed as follows:
Enable Alarm Output
Select the item to enable alarm relay output.
IR Cut Filter
Select the item and the camera’s IR cut filter (ICR) will be removed (on)
or blocked (off)
when alarm input is triggered.
Note:
The IR Function (Refer to IR Function
) could not be set as <Auto>
mode if this triggered action is enabled.
Send Message by FTP/E-Mail
The Administrator can select whether to send an alarm message by FTP and/or E-Mail
when an alarm is triggered.
Upload Image by FTP
Select this item and the Administrator can assign a FTP site and configure various
parameters. When the alarm is triggered, event images will be uploaded to the
appointed FTP site.
<Pre-trigger buffer> function allows users to check what happened to cause the trigger.
The <Pre-trigger buffer> frame rate could be pre-determined.
On the other hand, <Post-trigger buffer> is for users to upload certain amount of images
after the alarm input is triggered.
Check the box <Continue image upload> to upload the triggered images during certain
time or keep uploading until the trigger is off. Select <Upload for __sec> and enter the
duration in the blank. The images of the duration will be uploaded to FTP when the
alarm input is triggered. The setting range is from 1 to 9999 seconds. Select <Upload
during the trigger active> to make the images keep being uploaded to FTP during the