LevelOne FCS-1131 Manual - Page 53

Send Alarm Message by FTP/E-Mail, Upload Image by FTP, Upload Image by E-Mail

Get LevelOne FCS-1131 PDF manuals and user guides View all LevelOne FCS-1131 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 53 highlights

Select to set the recording duration after motion event occurs. The setting range is from 1 to 99999 seconds. Select to record the triggered video until the trigger is off. NOTE: Please make sure the local recording (with Micro SD/SDHC card) is activated so that this function can be implemented. Refer to Recording for further details.  Send Alarm Message by FTP/E-Mail The Administrator can select whether to send warning messages by FTP and/or E-Mail when motion is detected.  Upload Image by FTP Select this item and the Administrator can assign a FTP site and configure various parameters. When motion is detected, event images will be uploaded to the appointed FTP site. function allows users to check what happened to cause the trigger. The frame rate could be pre-determined. On the other hand, is for users to upload certain amount of images after motion event occurs. Check the box to upload the triggered images during certain time or keep uploading until the trigger is off. Select and enter the duration in the blank. The images of the duration will be uploaded to FTP when the motion event occurs. The setting range is from 1 to 9999 seconds. Select to make the images keep being uploaded to FTP during the trigger active until the event stops. Set the Image frequency as the upload frame rate. The setting range is from 1 frame to 15 frames. NOTE: Make sure FTP configuration has been completed. Refer to FTP for further details.  Upload Image by E-Mail Select this item and the Administrator can assign an e-mail address and configure 52

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
52
Select <Upload for __ sec> to set the recording duration after motion event occurs. The
setting range is from 1 to 99999 seconds.
Select <Upload during the trigger active> to record the triggered video until the trigger is
off.
NOTE:
Please make sure the local recording (with Micro SD/SDHC card)
is activated so that this function can be implemented. Refer to Recording
for further details.
Send Alarm Message by FTP/E-Mail
The Administrator can select whether to send warning messages by FTP and/or E-Mail
when motion is detected.
Upload Image by FTP
Select this item and the Administrator can assign a FTP site and configure various
parameters. When motion is detected, event images will be uploaded to the appointed
FTP site.
<Pre-trigger buffer> function allows users to check what happened to cause the trigger.
The <Pre-trigger buffer> frame rate could be pre-determined.
On the other hand, <Post-trigger buffer> is for users to upload certain amount of images
after motion event occurs.
Check the box <Continue image upload> to upload the triggered images during certain
time or keep uploading until the trigger is off. Select <Upload for __sec> and enter the
duration in the blank. The images of the duration will be uploaded to FTP when the
motion event occurs. The setting range is from 1 to 9999 seconds. Select <Upload
during the trigger active> to make the images keep being uploaded to FTP during the
trigger active until the event stops. Set the Image frequency as the upload frame rate.
The setting range is from 1 frame to 15 frames.
NOTE:
Make sure FTP configuration has been completed. Refer to FTP
for further details.
Upload Image by E-Mail
Select this item and the Administrator can assign an e-mail address and configure