Lexmark C762 Quick Reference Pages - Page 13

Con for TCP/IP

Get Lexmark C762 PDF manuals and user guides View all Lexmark C762 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

Connection guide Page 4 of 9 also provides important information that helps you configure for network printing. Note: If an optional MarkNet print server is installed, you see Print Net1 Setup on the display. 1 Make sure the printer is on. 2 Press Menu until you see Utilities Menu, and then press Select. 3 Press Menu until you see Print Net Setup, and then press Select. The network setup page prints and the printer returns to Ready status. 4 Check the first section on the network setup page and confirm that Status is "Connected." If Status is "Not Connected," your LAN drop may not be active or your network cable may be malfunctioning. Consult your network support person for a solution, and then print another network setup page to verify that you are connected to your network. Configure for TCP/IP If you have TCP/IP available on your network, we recommend that you assign an IP address to the printer. Assigning a printer IP address If your network is using DHCP, an IP address is automatically assigned after you connect the network cable to the printer. 1 Print a network setup page. 2 Look for the address under the "TCP/IP" heading on the network setup page. 3 Go to Verify printer setup on page 3 and begin with step 2. Note: You can find instructions for other methods of setting the IP address in the online documentation on the drivers CD that shipped with your printer. Launch the CD, and then click View Documentation Network Printer Install. If your network is not using DHCP, then you must manually assign an IP address to the printer. One of the easiest ways is to use the operator panel: 1 Press Menu until you see Network Menu, and then press Select. 2 Press Menu until you see Standard Network, and then press Select. Standard Network appears if you purchased a printer with a network port on the printer system board. If you have a MarkNet™ print server installed in the option card slot, you see Network Option 1. 3 Press Menu until you see Std Net Setup (or Network 1 Setup), and then press Select. 4 Press Menu until you see TCP/IP, and then press Select. 5 Press Menu until you see Set IP Address, and then press Select. 6 Change the address by pressing Menu to increase or decrease each number. Press Select to move to the next segment. Press Select when you are finished. The message Saved appears briefly. 7 Press Menu until you see Set IP Netmask, and then press Select. 8 Repeat step 6 to set the IP Netmask. 9 Press Menu until you see Set IP Gateway, and then press Select. 10 Repeat step 6 to set the IP Gateway. 11 When you are finished, press Go to return the printer to the Ready state.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
Connection guide
Page 4 of 9
also provides important information that helps you
configure for network printing.
Note:
If an optional MarkNet print server is
installed, you see
Print Net1 Setup
on
the display.
1
Make sure the printer is on.
2
Press
Menu
until you see
Utilities Menu
, and
then press
Select
.
3
Press
Menu
until you see
Print Net Setup
,
and then press
Select
. The network setup page
prints and the printer returns to
Ready
status.
4
Check the first section on the network setup
page and confirm that Status is “Connected.”
If Status is “Not Connected,” your LAN drop may
not be active or your network cable may be
malfunctioning. Consult your network support
person for a solution, and then print another
network setup page to verify that you are
connected to your network.
Configure for TCP/IP
If you have TCP/IP available on your network, we
recommend that you assign an IP address to the
printer.
Assigning a printer IP address
If your network is using DHCP,
an IP address is
automatically assigned after you connect the network
cable to the printer.
1
Print a network setup page.
2
Look for the address under the “TCP/IP” heading
on the network setup page.
3
Go to
Verify printer setup
on page 3 and begin
with step 2.
Note:
You can find instructions for other
methods of setting the IP address in the
online documentation on the drivers CD
that shipped with your printer. Launch
the CD, and then click
View
Documentation
Network Printer
Install
.
If your network is not using DHCP,
then you must
manually assign an IP address to the printer.
One of the easiest ways is to use the operator panel:
1
Press
Menu
until you see Network Menu, and
then press
Select
.
2
Press
Menu
until you see Standard Network,
and then press
Select
.
Standard Network appears if you purchased a
printer with a network port on the printer system
board. If you have a MarkNet™ print server
installed in the option card slot, you see
Network
Option 1
.
3
Press
Menu
until you see
Std Net Setup
(or
Network 1 Setup
), and then press
Select
.
4
Press
Menu
until you see
TCP/IP
, and then
press
Select
.
5
Press
Menu
until you see
Set IP Address
, and
then press
Select
.
6
Change the address by pressing
Menu
to
increase or decrease each number. Press
Select
to move to the next segment. Press
Select
when you are finished.
The message
Saved
appears briefly.
7
Press
Menu
until you see
Set IP Netmask
, and
then press
Select
.
8
Repeat step 6 to set the IP Netmask.
9
Press
Menu
until you see
Set IP Gateway
, and
then press
Select
.
10
Repeat step 6 to set the IP Gateway.
11
When you are finished, press
Go
to return the
printer to the Ready state.