LiftMaster CAPAC Installation Manual - English French Spanish - Page 10

Connecting CAPAC to Cellular, Select Cellular and click Next. See

Get LiftMaster CAPAC PDF manuals and user guides View all LiftMaster CAPAC manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

INTRODUCTION PRE-INSTALL NETWORK MOUNTING/POWER ACCESS CONTROL Connecting CAPAC to Cellular 1. On the CAPAC, press and hold the Reset/Learn button for 2 seconds to get to the access point page (the connectivity LED will blink green). 2. On your mobile device, go into the Wi-Fi configuration and look for the CAPAC Wi-Fi network. The Wi-Fi network format will be "MyQ-xxx," where xxx is the last three digits of your CAPAC's CP#. (See Figure 1) NOTE: If the "Internet may not be available" message displays, click keep WiFi connection. 3. Open a web browser (e.g., Edge, Chrome) and enter either setup.myqdevice.com or 192.168.1.1. (See Figure 2) NOTE: If you exit the CAPAC MyQ-xxx Wi-Fi network, open a new web browser and enter setup.myqdevice.com or 192.168.1.1 to restart your configuration. 4. To see the current Internet connection method, click Start. 5. From myQ® Business™, verify that the cellular service has been enabled for the CAPAC device. (See Figure 4) 6. Select Cellular and click Next. (See Figure 3) NOTE: This can take up to 15 minutes. 7. When connected properly, a congratulation message indicates that your device is connected. The LED next to the blue power LED will be solid on the CAPAC housing. Follow directions to troubleshoot issues if needed. (See Figure 5) NOTE: The color of the LED indicates cellular signal strength. Red indicates fair connectivity, Amber/Orange indicates good connectivity, and Green indicates excellent connectivity. NOTE: If the CAPAC fails to connect to cellular, ensure the cellular subscription is activated in myQ Business. If subscription is active, see the section in the next page on how resolve cellular connectivity. Reset/Learn Button (back) OUTPUT WIEGAND INPUT GATE 1 OUTPUT 2 SDA SCL NO COM NC NO COM NC 1 WIEGAND 2 D1 COM D0 D1 COM D0 INPUT POWER 1 GND 2 GND 12V-24V POWER ETHERNET Figure 1 Figure 2 Figure 3 10 Figure 4 Figure 5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
10
ACCESS CONTROL
MOUNTING/POWER
NETWORK
PRE-INSTALL
INTRODUCTION
Connecting CAPAC to Cellular
1.
On the CAPAC, press and hold the Reset/Learn button for 2 seconds to get
to the access point page (the connectivity LED will blink green).
2.
On your mobile device, go into the Wi-Fi configuration and look for the CAPAC
Wi-Fi network. The Wi-Fi network format will be “MyQ-xxx,” where xxx is the
last three digits of your CAPAC’s CP#. (See Figure 1)
NOTE:
If the “Internet may not be available” message displays, click keep Wi-
Fi connection.
3.
Open a web browser (e.g., Edge, Chrome) and enter either
setup.myqdevice.com or 192.168.1.1. (See Figure 2)
NOTE:
If you exit the CAPAC MyQ-xxx Wi-Fi network, open a new web browser
and enter setup.myqdevice.com or 192.168.1.1 to restart your configuration.
4.
To see the current Internet connection method, click Start.
5.
From myQ® Business™, verify that the cellular service has been enabled for
the CAPAC device. (See Figure 4)
6.
Select Cellular and click Next. (See Figure 3)
NOTE:
This can take up to 15 minutes.
7.
When connected properly, a congratulation message indicates that your device
is connected. The LED next to the blue power LED will be solid on the CAPAC
housing. Follow directions to troubleshoot issues if needed. (See Figure 5)
NOTE:
The color of the LED indicates cellular signal strength. Red indicates
fair connectivity, Amber/Orange indicates good connectivity, and Green
indicates excellent connectivity.
NOTE:
If the CAPAC fails to connect to cellular, ensure the cellular
subscription is activated in myQ Business. If subscription is active, see the
section in the next page on how resolve cellular connectivity.
INPUT
OUTPUT
WIEGAND
GATE
SDA SCL
OUTPUT
NO COM NC
NO COM NC
1
2
D1 COM D0
D1 COM D0
1
2
WIEGAND
1
GND
2
INPUT
GND 12V-24V
POWER
POWER
ETHERNET
Reset/Learn Button (back)
Figure 1
Figure 2
Figure 3
Figure 4
Figure 5