Home » LiftMaster Manuals » Garage Door Openers » LiftMaster EL2000 » Manual Viewer

LiftMaster EL2000 EL25-KEYPAD PROGRAMMING Manual - Page 54

Features, Set Anti-Passback Entry/Exit for Specific Devices: 64, Set Anti-Passback Time: 13

View all LiftMaster EL2000 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 54 highlights

Features Features Features Setting Anti-Passback The Anti-Passback feature deters someone from "passing back" his/her access code/ card to unauthorized individuals so they can gain entry into a restricted area. There are 2 types of anti-passback features: • True Anti-Passback requires residents to exit before entering again (and vice versa). For example, if you have a door with Card Reader 1 (to enter) and Card Reader 2 (to exit), a resident entering with Card Reader 1 will have to swipe his/her card in the Card Reader 2 to exit before swiping on Card Reader 1 again (and vice versa). • Timed Anti-Passback requires residents to wait a defined period of time before using the same access code (card, entry code, etc.) again on the same entry device (reader, keypad, etc). For example, if you set the Timed Anti-Passback to 60 minutes, the system will not grant access for 60 minutes to anyone who tries to reenter the same code into the same reader. Enable or Disable Anti-Passback: 12 Enable or disable the anti-passback feature. You may only enable the door(s) for timed or true anti-passback. Factory Setting: Disabled 1 Press Then 2 Enable True Enable (1) or Disable (0). Then (#) 3 Enable Timed Enable (1) or Disable (0). Then (#) Example: 1 2 3 Enables Timed Anti-Passback. Set Anti-Passback Entry/Exit for Specific Devices: 64 Set the anti-passback to function for specified entry devices (e.g., card readers, keypads, etc.). When setting devices for "true" anti-passback, set one device for "entry" and the other for "exit". Only Wiegand devices may use true anti-passback. Factory Setting: Disabled Important: The Anti-Passback feature will not function unless you enable Program Number 12 (see above). 1 Press Then 2 Enter Entry Device (0-4). Then (#) Example: 3 Enter Anti-Passback Option. Then (#) Disabled=0 True Anti-Passback Entrance=2 Timed Anti-Passback=1 True Anti-Passback Exit=3 1 2 3 Sets Device "1" for Timed Anti-Passback. Set Anti-Passback Time: 13 With "timed" anti-passback, after a resident uses a card/code/transmitter on a specific entry device, they cannot use the device again until a specified amount of time elapses. Factory Setting: 3 Minutes 1 Press Then 2 Enter Number of Minutes (1-60). Then (#) Page 53

Section	Page
Keypad Programmiing Manual for EL Models	1
Keypad Programming Guide	2
Table of Contents	3
Table of Contents Continued	4
Quick Reference Guide for Keypad Programming the Units	5
Quick Reference Continued	6
Quick Reference Continued	7
Quick Reference Continued	8
Quick Reference Continued	9
Introduction	10
Multi-Resident Complex (Dial-Out)	10
Multi-Resident Complex (Manager Sharing)	11
NPB Multi-Resident Complex	11
Single Family Residence (NPB) Example	12
Multi-Resident Complex Example	13
Your System Layout	14
Programming Single Unit Overview	15
Programming Basics	15
Procedure Required to Program EL Models:	16
Enter Programming Mode	17
Exit Programming Mode	17
System Feedback / Responses (Beeps)	18
Other Response:	18
Visual Responses:	18
Direct Command Responses:	19
Visitor Responses:	19
Sending Direct Commands from the Resident’s Phone	20
Programming Multiple Units Overview	21
Verify Unit Number: 111	21
Setup “Your Settings”	22
Change the Unit’s ID and Chain Number for Multiple Unit Configurations ONLY: 2	22
Setup External Access Control Devices	23
What is a Relay?	23
Configuring \	24
Step 1 Set Each \	24
Step 2 Set Each Relay’s \	24
Step 3 Assign \	25
Step 4 Assign Each External Access Control Device a \	25
\	26
Unit Controlling 1 Door	27
Unit Controlling 2 Doors and Vehicle Gate	27
Unit Controlling 4 Doors	28
Directory Codes	29
Set Directory Code Length	30
Add, Edit or Delete Directory Codes	30
Add Basic Directory Code: 40	30
Add or Edit Full Function Directory Code: 41	31
Change a Directory Code ONLY: 44	31
Delete a Directory Code: 48	31
Delete ALL Directory Codes: 201	32
Enable or Disable Do Not Disturb Schedule	32
Enable or Disable Call Forwarding (Directory Calls)	32
Add / Modify Resident DnD and/or Call Forwarding	33
Activate or Deactivate a Directory Code	33
Directory Code Display Option	34
Resident Display Option	34
Entry Codes	35
Set an Entry Code Length	36
Add, Edit or Delete Entry Codes	36
Add a Basic Entry Code: 50	36
Add or Edit Full Function Entry Code: 51	37
Change Entry Code ONLY: 54	37
Delete an Entry Code: 57	37
Change Entry Code Door Access: 75	37
Assign Utility Option: 58	38
Assign Special Use Entry Code at the Unit Keypad: 59	38
Delete ALL Entry Codes: 202	39
Activate or Deactivate an Entry Code	39
Verify an Entry Code	39
Access Cards	40
Add, Edit or Delete Cards	41
Add a Basic Card: 80	41
Add or Edit a Full Function Card: 81	42
Add a Group of Cards at Once: 82	42
Delete a Card: 88	43
Delete ALL Cards: 203	43
Activate or Deactivate a Card	43
Verify a Card	44
Facility Codes	44
Card Types	44
Transmitters	45
Add, Edit or Delete Transmitter	46
Add a Basic Transmitter: 90	46
Add or Edit a Full Function Transmitter: 91	47
Add or Edit a Group of Full Function Transmitters: 94	47
Delete a Transmitter: 100	48
Delete ALL Transmitters: 204	48
Activate or Deactivate a Transmitter	49
Verify a Transmitter	49
Time Zones, Holidays and Clock	50
Creating Time Zones	51
Setting Holidays	51
Assigning Door Use and Unlock Time Zone	52
Enable or Disable Unlock Schedule: 11	52
Assign Door Auto Lock / Unlock Schedule: 31	52
Deleting ALL Time Zones	53
Setting the Clock	53
Enable or Disable Daylight Saving Time: 4	53
Features	54
Set Anti-Passback Entry/Exit for Specific Devices: 64	54
Set Anti-Passback Time: 13	54
Enable or Disable Anti-Passback Forgiveness at Midnight: 105	55
Enable or Disable Utility Option: 58	55
Configure the Alarm Features	55
Configure “Door Forced Open” Alarm Feature: 103	56
Setting “Strikes and Out” (Number of Entry Code Attempts before Disabling Unit): 17	56
Configure “Strikes and Out” Alarm Feature: 104	56
Change or Verify the Unit’s Password	57
Communications To and From Unit	58
Number of Rings Before Unit Answers: 16	59
Override Telephone Company Answering Service: 109	59
Enable or Disable Telco Mode: 20	59
Dial \	59
Set a Phone Number’s Extension Delay Time: 110	60
Speaker / Microphone Settings	60
Enable or Disable Call Waiting	60
Visitor Communication Settings	61
Set Visitor Talk Time: 5	62
Enable or Disable “Announce All Doors/Access Granted” 26	62
Set Display Greeting: 160	62
Return to Menu Programming: 25	62
LCD Visitor Messages	63
LCD Visitor Messages (continued)	64
Postal Lock/Autocall/Exit/Door Sensor Devices	65
Autocall Device	65
Request to Exit Device (REX)	66
Door Sensing Devices	67
Direct Commands From The Phone	68
Speaking Through the Unit (Intercom Mode): 120	68
Direct Commands from Your Phone: 120 121 122	69
Direct Commands from Your Phone (continued): 123 124 125 126	70
Real-Time Monitoring	71
Reset/Restore the Unit and Database	72
Reset the Unit: 29	72
Delete ALL Access Codes from Database: 206	72
Keypad Template	73
Notes	74
Glossary	76
Glossary Continued	77
Appendix	78

Match case Limit results 1 per page

Page 53

Features

The Anti-Passback feature deters someone from "passing back" his/her access code/

card to unauthorized individuals so they can gain entry into a restricted area. There

are

types of anti-passback features:

•

True Anti-Passback requires residents to exit before entering again (and vice versa).

For

example, if you have a door with Card Reader 1 (to enter) and Card Reader 2 (to exit), a resident

entering with Card Reader 1 will have to swipe his/her card in the Card Reader 2 to exit before

swiping on Card Reader 1 again (and vice versa).

•

Timed Anti-Passback requires residents to wait a defined period of time before using the same

access code (card, entry code, etc.) again on the same entry device (reader, keypad, etc).

For

example, if you set the Timed Anti-Passback to 60 minutes, the system will not grant access for

60 minutes to anyone who tries to reenter the same code into the same reader.

Setting Anti-Passback

Features

Enable or Disable Anti-Passback:

Press

Then

Enable True Enable (

) or Disable (

). Then (#)

Enable or disable the anti-passback feature. You may only enable the door(s) for timed

or true anti-passback.

Factory Setting: Disabled

Example:

Enables Timed Anti-Passback.

Set Anti-Passback Entry/Exit for Specific Devices:

Press

Then

Enter Entry Device (0-4).

Then (#)

Example:

Sets Device "1" for Timed Anti-Passback.

Set the anti-passback to function for specified entry devices (e.g., card readers, keypads,

etc.). When setting devices for "true" anti-passback, set one device for "entry" and the

other for "exit". Only Wiegand devices may use true anti-passback.

Factory Setting: Disabled

Important:

The Anti-Passback feature will not function unless you enable Program

Number

(see above).

Enter Anti-Passback Option. Then (#)

Disabled=

True Anti-Passback Entrance=

Timed Anti-Passback=

True Anti-Passback Exit=

Set Anti-Passback Time:

Press

Then

Enter Number of Minutes (1-60). Then (#)

With "timed" anti-passback, after a resident uses a card/code/transmitter on a specific

entry device, they cannot use the device again until a specified amount of time elapses.

Factory Setting: 3 Minutes

Enable

Timed

Enable (

) or

Disable (

). Then (#)