LiftMaster GH GT- Logic 4 Installation Manual - Page 31

PROGRAMMING REMOTE CONTROLS NOTE: The following programming requires a LiftMaster Monitored Entrapment Protection (LMEP) device. Your 315 MHz Security✚® or dip switch remote control can be programmed to operate as a 3-button wireless control station: the large button will open the door, the middle button will close the door, and the third button will stop the door's movement. You may set up this feature as follows: 1. To enter programming press and release the RADIO button on the logic board (the RADIO LED will light). 2. To program the OPEN button to a remote control press and release the OPEN button on the logic board. The RADIO LED will flash and then stay on solid. Then press the corresponding button on the remote control. The RADIO LED on the logic board will flash, this confirms that the remote control has been programmed. (By programming the remote you use 1 channel of the 23 channels on the radio receiver.) 3. To program the CLOSE button to a remote control press and release the CLOSE button on the logic board. The RADIO LED will flash and then stay on solid. Then press the corresponding button on the remote control. The RADIO LED on the logic board will flash, this confirms that the remote control has been programmed. (By programming the remote you use 1 channel of the 23 channels on the radio receiver.) 4. To program the STOP button to a remote control press and release the STOP button on the logic board. The RADIO LED will flash and then stay on solid. Then press the corresponding button on the remote control. The RADIO LED on the logic board will flash, this confirms that the remote control has been programmed. (By programming the remote you use 1 channel of the 23 channels on the radio receiver.) 5. After learning remote controls press the RADIO button on the logic board (RADIO LED will turn off). NOTE: If no activity within 30 seconds the radio will automatically exit programming mode. DATA SLOT 1 SLOT 2 OPEN CLOSE STOP Open Close Stop MER NABLE EDGE: OPEN CLOSE STOP COMMON REV MOTOR STD DIRECTION OLS MID SLS 3-PHASE 1-PHASE 24VAC POWER 24VAC TIMER DEFEAT COMMON MAS CLS LMEP: MRT MID TTC TIMER ENABLE EDGE: OPEN RADIO 1 2 3 CLOSE T E2 D1 C2 B2 TS FSTS DIAG OPTN PROG STOP COMMON RELAY A RELAY B SBC REMOTE CONTROL PROGRAMMING FEATURE Program Remote Controls from the 3-button control station (3BCS). This feature allows the user to add additional remote controls from the 3BCS. By default the remote control learn option is off. NOTE: Requires access to the operator electrical box to enable or disable this feature. To turn this feature on: 1. Turn the SELECTOR DIAL to PROG. 2. Press and release the RADIO button. The RADIO LED will be lit. 3. Press and release the MID button. The RADIO LED will flash quickly 6 times. 4. Press and release the RADIO button. The RADIO LED will turn off. 5. Return the SELECTOR DIAL to the desired wiring type. To add remote controls from the 3BCS: 1. With the door in the fully closed position (close limit activated), press and hold STOP. 2. While holding STOP, press and hold CLOSE. 3. While holding STOP and CLOSE, press and hold OPEN. 4. Release all three buttons once the MAS LED has lit. 5. Learn a remote control by one of the following methods: a. Programming a standard single button/single function remote control, push and hold the remote control button until the MAS LED goes out. Repeat steps 1 through 4 to add additional remote controls. b. Programming a 3-button/three function remote control (OPEN/CLOSE/STOP), first push the button on the 3BCS (Example: OPEN) and then press and hold the button on the remote control (Example: large button) that you want to correspond with the selected (Example: OPEN) command until the MAS LED flashes and goes out. Repeat steps 1 through 4 to add additional buttons (CLOSE AND STOP). To turn this feature off: 1. Turn the SELECTOR DIAL to PROG. 2. Press and release the RADIO button. The RADIO LED will be lit. 3. Press and release the MRT button. The RADIO LED will flash quickly 3 times. 4. Press and release RADIO button. The RADIO LED will turn off. 5. Return SELECTOR DIAL to desired wiring type. NOTE: Restoring the operator to Factory Default (see RESETTING FACTORY DEFAULTS) will also disable this feature. The remote controls will still be learned. PROGRAMMING Programming - Remote controls 31