LiftMaster MTF Installation Manual - Page 6

Features, Tools Needed, And Operator Specifications

Get LiftMaster MTF PDF manuals and user guides View all LiftMaster MTF manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

INTRODUCTION FEATURES, TOOLS NEEDED, AND OPERATOR SPECIFICATIONS FEATURES • Full service controller with eight inputs and LED indicators for loops, card reader, radio, etc. • Reversible arm direction for right or left handed operation. • Instant Reverse Device (IRD) monitor senses obstructions during motion. • Fail safe (auto open on AC power failure). • Raise gate input memory will memorize multiple vehicles - ideal for bar code scanners and AVI. • Ability to STOP arm in close travel if tail-gating is sensed at close loop. • Anti-tail gate alarm - fires K1 relay to trigger a warning device when tail-gating is sensed. • SAMS with "memory" - allows MATTS to open a slide/swing gate first then raises arm. • Dynamic motor braking to preserve arm positioning. • Direct drive gear reducer eliminates many parts that might otherwise fail. • State of the art MOSFET motor drive technology, NO contactors or relays. • Soft start and stop in open and close travel motions. • No limit switches to fail - uses magnetic (Hall Effect) sensors to monitor arm position. • Maximum Run Timer for motor with anti-tamper protection in closing direction. • Each operator configurable as primary or second operator. • LED diagnostics for easy troubleshooting. • Adjustable Timer-To-Close with on/off selection. • Transient voltage protection on all inputs. TOOLS NEEDED During assembly, installation, and adjustment of the operator, the tools listed below may be needed. • 9/16" Wrench for Spike System Coupler and Turnbuckle Jam Nuts • 9/16" Socket for Top Plate • 7/16" Socket for Guide Roller • 9/16" Wrench for 3/8" Anchors • 4.5 mm Allen Wrench • 3/16" Allen Wrench • Precision Screwdrivers (Phillips and Flat Head) • Cable Cutters and Strippers OPERATOR SPECIFICATIONS This model is intended for use in vehicular gate applications. • Intended Usage Class II, III, IV • High torque 24 volt Permanent Magnet DC motor • On 120 Vac installations, unswitched duplex outlet gives convenient supply for 120 Vac accessories • Built in battery run - inherent 24 Vdc backup power with regulated 24 Vdc for accessories • Capable of being powered from 120 (or 230 Vac when separately purchased accessory installed), 230 Vac, or UL Listed Class 2 Solar Power • Break away mount design for the 12-15 foot x 3 inch tubular aluminum barrier arm • Heater option MUST be used if temperature is 30° or below. Heater option available for 120 Vac operators ONLY. Refer to Accessories page. • All rust proof aluminum construction with white powder coat baked on enamel. Molded Polyethylene UV stabilized cover never needs wax or paint (excludes towers). MTS/MTF 3-1/2" 13-1/2" FRONT VIEW 14-1/4" 42" 13-1/2" SIDE VIEW 42" 36-1/2" 6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
6
•
Full service controller with eight inputs and LED indicators for loops,
card reader, radio, etc.
•
Reversible arm direction for right or left handed operation.
•
Instant Reverse Device (IRD) monitor senses obstructions during
motion.
•
Fail safe (auto open on AC power failure).
•
Raise gate input memory will memorize multiple vehicles – ideal for
bar code scanners and AVI.
•
Ability to STOP arm in close travel if tail-gating is sensed at close loop.
•
Anti-tail gate alarm - fires K1 relay to trigger a warning device when
tail-gating is sensed.
•
SAMS with “memory” - allows MATTS to open a slide/swing gate first
then raises arm.
•
Dynamic motor braking to preserve arm positioning.
•
Direct drive gear reducer eliminates many parts that might otherwise
fail.
•
State of the art MOSFET motor drive technology, NO contactors or
relays.
•
Soft start and stop in open and close travel motions.
•
No limit switches to fail - uses magnetic (Hall Effect) sensors to
monitor arm position.
•
Maximum Run Timer for motor with anti-tamper protection in closing
direction.
•
Each operator configurable as primary or second operator.
•
LED diagnostics for easy troubleshooting.
•
Adjustable Timer-To-Close with on/off selection.
•
Transient voltage protection on all inputs.
•
9/16" Wrench for Spike System Coupler and Turnbuckle Jam Nuts
•
9/16" Socket for Top Plate
•
7/16" Socket for Guide Roller
•
9/16" Wrench for 3/8" Anchors
FEATURES
• 4.5 mm Allen Wrench
• 3/16" Allen Wrench
•
Precision Screwdrivers (Phillips and Flat Head)
• Cable Cutters and Strippers
TOOLS NEEDED
During assembly, installation, and adjustment of the operator, the tools listed below may be needed.
This model is intended for use in vehicular gate applications.
•
Intended Usage Class II, III, IV
•
High torque 24 volt Permanent Magnet DC motor
•
On 120 Vac installations, unswitched duplex outlet gives convenient
supply for 120 Vac accessories
•
Built in battery run - inherent 24 Vdc backup power with regulated 24
Vdc for accessories
•
Capable of being powered from 120 (or 230 Vac when separately
purchased accessory installed), 230 Vac, or UL Listed Class 2 Solar
Power
•
Break away mount design for the 12-15 foot x 3 inch tubular
aluminum barrier arm
•
Heater option MUST be used if temperature is 30° or below. Heater
option available for 120 Vac operators ONLY. Refer to Accessories
page.
•
All rust proof aluminum construction with white powder coat baked
on enamel. Molded Polyethylene UV stabilized cover never needs wax
or paint (excludes towers).
OPERATOR SPECIFICATIONS
MTS/MTF
42"
13-1/2"
14-1/4"
36-1/2"
42"
13-1/2"
3-1/2"
FRONT
VIEW
SIDE VIEW
INTRODUCTION
FEATURES, TOOLS NEEDED, AND OPERATOR SPECIFICATIONS