MSI MEG X570S ACE MAX User Manual - Page 49

JCI1: Chassis Intrusion Connector, JDASH1 : Tuning Controller connector

Get MSI MEG X570S ACE MAX PDF manuals and user guides View all MSI MEG X570S ACE MAX manuals
Add to My Manuals
Save this manual to your list of manuals

Page 49 highlights

JCI1: Chassis Intrusion Connector This connector allows you to connect the chassis intrusion switch cable. Normal (default) Trigger the chassis intrusion event Using chassis intrusion detector 1. Connect the JCI1 connector to the chassis intrusion switch/ sensor on the chassis. 2. Close the chassis cover. 3. Go to BIOS > SETTINGS > Security > Chassis Intrusion Configuration. 4. Set Chassis Intrusion to Enabled. 5. Press F10 to save and exit and then press the Enter key to select Yes. 6. Once the chassis cover is opened again, a warning message will be displayed on screen when the computer is turned on. Resetting the chassis intrusion warning 1. Go to BIOS > SETTINGS > Security > Chassis Intrusion Configuration. 2. Set Chassis Intrusion to Reset. 3. Press F10 to save and exit and then press the Enter key to select Yes. JDASH1 : Tuning Controller connector This connector is used to connect an optional Tuning Controller module. 2 14 1 13 1 No Pin 2 3 MCU_SMB_SCL_M 4 5 VCC5 6 7 PSIN#_R 8 9 OC_RETRY# 10 11 BLK+ 12 13 CLRCMOS_EN 14 NC MCU_SMB_SDA_M Ground FP_RST#_R OC_FS BLKNC Overview of Components 49

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
49
Overview of Components
JCI1: Chassis Intrusion Connector
This connector allows you to connect the chassis intrusion switch cable.
Normal
(default)
Trigger the chassis
intrusion event
Using chassis intrusion detector
1.
Connect the
JCI1
connector to the chassis intrusion switch/ sensor on the chassis.
2.
Close the chassis cover.
3.
Go to
BIOS > SETTINGS > Security > Chassis Intrusion Configuration
.
4.
Set
Chassis Intrusion
to
Enabled
.
5.
Press
F10
to save and exit and then press the
Enter
key to select
Yes
.
6.
Once the chassis cover is opened again, a warning message will be displayed on
screen when the computer is turned on.
Resetting the chassis intrusion warning
1.
Go to
BIOS > SETTINGS > Security > Chassis Intrusion Configuration
.
2.
Set
Chassis Intrusion
to
Reset
.
3.
Press
F10
to save and exit and then press the
Enter
key to select
Yes
.
JDASH1 : Tuning Controller connector
This connector is used to connect an optional Tuning Controller module.
1
2
14
13
1
No Pin
2
NC
3
MCU_SMB_SCL_M
4
MCU_SMB_SDA_M
5
VCC5
6
Ground
7
PSIN#_R
8
FP_RST#_R
9
OC_RETRY#
10
OC_FS
11
BLK+
12
BLK-
13
CLRCMOS_EN
14
NC