Mackie Onyx 820i Owner's Manual - Page 34

Appendix D: Rack Ear installation instructions

Get Mackie Onyx 820i PDF manuals and user guides View all Mackie Onyx 820i manuals
Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

Appendix D: Rack Ear installation instructions The optional Rack Ear Kit allows the Onyx 820i mixer to be mounted in a standard 19" rack. It will be out of harm's way and the band may continue tearin' it up without fearing any consequences. The mixer takes up nine rack spaces. Be sure to allow for an extra space or two above to make connections. The kit contains two rack ear brackets and eight black screws (M3.5 x 8mm). Tools Required: One phillips screwdriver, two bales of hay, cheese and crackers, and a box of wine (optional). Procedure: 1. Turn off the mixer and disconnect all cords. 2. Place the mixer face up on a soft and dry flat surface. 3. Remove the eight silver screws as shown below, wrap them up in an old sock, and keep them in a safe place for further use. 4. Using only the new screws supplied, secure the rack ear brackets to each side of the mixer as shown. Hand-tighten the screws securely. The brackets are identical, so it does not matter which one goes on which side. 5. Offer up the mixer to the rack and secure it in place with four rack screws (not supplied). Remember to leave enough room at the top to attach the AC power cord and any other connections needed. 6. This might be a good time to sit on one of the bales of hay and enjoy the cheese, crackers, and boxed wine! 7. Cross this off the 'to do' list and move on to the next project. 34 Onyx 820i

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
34
Onyx 820i
The optional Rack Ear Kit allows the Onyx 820i mixer
to be mounted in a standard 19” rack. It will be out of
harm’s way and the band may continue tearin’ it up
without fearing any consequences. The mixer takes up
nine rack spaces. Be sure to allow for an extra space or
two above to make connections. The kit contains two
rack ear brackets and eight black screws (M3.5 x 8mm).
Tools Required:
One phillips screwdriver, two bales of hay, cheese and
crackers, and a box of wine (optional).
Procedure:
1.
Turn off the mixer and disconnect all cords.
2.
Place the mixer face up on a soft and dry flat
surface.
Appendix D: Rack Ear installation instructions
3.
Remove the eight silver screws as shown below,
wrap them up in an old sock, and keep them in
a safe place for further use.
4.
Using only the new screws supplied, secure the
rack ear brackets to each side of the mixer as
shown. Hand-tighten the screws securely. The
brackets are identical, so it does not matter
which one goes on which side.
5.
Offer up the mixer to the rack and secure it
in place with four rack screws (not supplied).
Remember to leave enough room at the top to
attach the AC power cord and any other con-
nections needed.
6.
This might be a good time to sit on one of the
bales of hay and enjoy the cheese, crackers, and
boxed wine!
7.
Cross this off the ‘to do’ list and move on to the
next project.