Magnavox MFX450 User manual, English (US) - Page 24

Tuner

Get Magnavox MFX450 - Audio System PDF manuals and user guides View all Magnavox MFX450 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

English MFX450_eng 11/26/02 3:21 AM Page 23 TUNER Tuning to radio stations You can search for radio stations by scanning the frequency band. You can also key in the frequency of a known radio station. If an FM station is being broadcast and received in stereo, STEREO is shown. Searching for radio stations 1 Turn SOURCE SELECT to select the tuner. yTUNER is displayed. 2 Select a waveband by pressing TUNER BAND repeatedly. yThe selected waveband is displayed. 3 Keep 1 or 2 pressed for approximately 1 second. ySEARCH is displayed and the tuner tunes to a station with sufficient strength. 4 Repeat this procedure until you find the desired station. • To fine tune to a weak transmitter, briefly press 1 or 2 as often as necessary for optimum reception. Tuning to a radio station by frequency (with the remote control only) 1 Press TUNER. yTUNER is displayed. 2 Press FR. D.. y_ is displayed. 3 Use 1-0 to key in the frequency of a radio station. Notes: Only valid numbers within the frequency range of the tuner can be keyed in. Switching FM sensitivity You can switch the tuner to a lower search sensitivity, to search only for stations with a strong signal (FM only). 1 Turn SOURCE SELECT to select the tuner. yTUNER is displayed. 2 Press SENS. on the receiver. yEither SENS HI or SENS LO is displayed for 5 seconds. Note: While searching for radio stations, the actual sensitivity is displayed. In this case, SENS LO means the tuner is looking only for radio stations with a strong signal. Storing radio stations You may store up to 30 radio stations in the memory. The receiver can select and program radio stations by itself or you can choose them yourself. Automatic programming 1 Choose * TUNER from the menu and press NEXT 2. 2 Choose AUTO INSTALL and press NEXT 2. yThe preset number where programming will start, the waveband and AUTO are displayed. 3 Turn TUNER PRESET X to change the preset number where programming should start. 4 Use TUNER BAND to switch to the desired waveband. 5 Press ENTER / OK to start programming. yAUTO INSTALL flashes and all available radio stations are programmed, this may take a few minutes. Programming is done when AUTO INSTALL stops flashing. Manual programming 1 Choose * TUNER from the menu and press NEXT 2. 2 Choose MAN INSTALL and press NEXT 2. yA preset number, the waveband and the frequency are displayed. 3 Turn TUNER PRESET X to change to the preset number where the radio station should be stored. 4 Tune to the desired radio station (see "Searching for radio stations"). 5 Press ENTER / OK to confirm your selection. ySTORED is displayed briefly. The radio station is programmed at the chosen preset number. 6 Select and store all desired radio stations this way. 23

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
23
English
TUNER
You can search for radio stations by scanning the frequency
band. You can also key in the frequency of a known radio
station. If an FM station is being broadcast and received in
stereo,
STEREO
is shown.
Searching for radio stations
1
Turn SOURCE SELECT to select the tuner.
y
TUNER
is displayed.
2
Select a waveband by pressing TUNER BAND repeatedly.
y
The selected waveband is displayed.
3
Keep
1
or
2
pressed for approximately 1 second.
y
SEARCH
is displayed and the tuner tunes to a station
with sufficient strength.
4
Repeat this procedure until you find the desired station.
•
To fine tune to a weak transmitter, briefly press
1
or
2
as
often as necessary for optimum reception.
Tuning to a radio station by frequency (with the remote
control only)
1
Press TUNER.
y
TUNER
is displayed.
2
Press FR. D..
y
_
is displayed.
3
Use 1
–
0 to key in the frequency of a radio station.
Notes: Only valid numbers within the frequency range of the
tuner can be keyed in.
You can switch the tuner to a lower search sensitivity, to
search only for stations with a strong signal (FM only).
1
Turn SOURCE SELECT to select the tuner.
y
TUNER
is displayed.
2
Press SENS. on the receiver.
y
Either
SENS HI
or
SENS LO
is displayed for 5 seconds.
Note: While searching for radio stations, the actual sensitivity
is displayed. In this case,
SENS LO
means the tuner is
looking only for radio stations with a strong signal.
You may store up to 30 radio stations in the memory. The
receiver can select and program radio stations by itself or you
can choose them yourself.
Automatic programming
1
Choose
* TUNER
from the menu and press NEXT
2
.
2
Choose
AUTO INSTALL
and press NEXT
2
.
y
The preset number where programming will start, the
waveband and
AUTO
are displayed.
3
Turn TUNER PRESET
X
to change the preset number where
programming should start.
4
Use TUNER BAND to switch to the desired waveband.
5
Press ENTER / OK to start programming.
y
AUTO INSTALL
flashes and all available radio
stations are programmed, this may take a few minutes.
Programming is done when
AUTO INSTALL
stops
flashing.
Manual programming
1
Choose
* TUNER
from the menu and press NEXT
2
.
2
Choose
MAN INSTALL
and press NEXT
2
.
y
A preset number, the waveband and the frequency are
displayed.
3
Turn TUNER PRESET
X
to change to the preset number
where the radio station should be stored.
4
Tune to the desired radio station (see
“
Searching for radio
stations
”
).
5
Press ENTER / OK to confirm your selection.
y
STORED
is displayed briefly. The radio station is
programmed at the chosen preset number.
6
Select and store all desired radio stations this way.
Storing radio stations
Switching FM sensitivity
Tuning to radio stations
MFX450_eng
11/26/02 3:21 AM
Page 23