Marantz PMD340 User Guide - Page 23

ENGLISH ENGLISH FRANCAIS FRANCAIS ESPANOL ESPANOL PORTUGUES PORTUGUES Fader Start The Fader Start input can be used to play or pause the CD player by connecting it to a mixer or mixing console equipped with a fader start output. A customized switch can also be created for applications where a fader start output is not available. Tip: To enable the input from the fader switch, set preset menu No.16 "Remote:" to "On". (See also page 17) Connection to the PMD330 ANALOG OUTPUT L R DIGITAL OUTPUT (SPDIF) REMOTE FADER START RC5 IN INT (IR)5 EXT OUT FADER switch Fader start polarity Play Closed Pause Open Connection to the PMD331/PMD340 When using control port pin 10 FADER (NORMAL) and pin 25 (TALLY COMMON) ANALOG OUTPUT R DIGITAL OUTPUT (SPDIF) CONNECTION 1 GND 12 2 HOT(+) L 3 3 COLD(-) RC5 REMOTE L BALANCED R L R BALANCED OUTPUT LEVEL INT (IR) EXT IN OUT CONTROL I/O FADER (NORMAL) switch Fader start polarity Play Closed Pause Open Connection to the PMD331/PMD340 When using control port pin 23* FADER (INVERT) and pin 25 (TALLY COMMON) ANALOG OUTPUT R DIGITAL OUTPUT (SPDIF) CONNECTION 1 GND 12 2 HOT(+) L 3 3 COLD(-) RC5 REMOTE L BALANCED R L R BALANCED OUTPUT LEVEL INT (IR) EXT IN OUT CONTROL I/O FADER (INVERT) switch Fader start polarity Play Open Pause Closed Troubleshooting The following is the troubleshooting list. Sometimes, an unintentional mistake in the operation of the CD player could lead you to think that it was malfunctioning. This device contains a microcomputer chip. If you suspect that static electricity may have caused the CD player to operate incorrectly, turn the power off, wait at least thirty seconds, and then turn the power back on. The disc does not play. 1. Is the power cord connected properly? 2. Is the POWER switch on? 3. Is the disc positioned correctly? 4. Is the disc right side up? (The disc label should be facing up.) 5. Is the disc dirty? 6. Is the disc damaged? 7. Is the disc warped? The disc play, but there is no sound. 1. Are the amp and speakers connected properly? 2. Is the amp power switch on? 3. Is the amp function or selector switch set to "CD" or "AUX" (whichever corresponds to the jacks to which you connected the CD player)? 4. Is the amp volume set properly? The disc suddenly stops. 1. Is the disc dirty? 2. Is the disc damaged? 3. Is the disc warped? There is no sound at all, or there is sudden noise during the music. 1. Is the disc dirty or damaged? 2. Is the disc warped? 3. Is the CD an audio CD? This CD player cannot play personal computer CD-ROMs or DTS-CDs, etc. The remote control does not work. 1. Is the window on the remote control transmitter pointing properly at the sensor on the CD player? Is there an obstacle between the remote control transmitter and the CD player? 2. Are the batteries in the remote control still in good condition? 3. Is there a strong light source shining on the remote control sensor? 4. Is the INT/EXT switch set to INT? The CD player will not play a CD-R/CD-RW disc. 1. Is the disc right side up? (The disc label should be facing up.) 2. Has the disc been properly finalized (i.e., was the TOC written on the disc)? 3. Is the data recorded on the disc in a audio (CD-DA) format? DEUTSCH DEUTSCH ITALINO ITALINO NEDERLANDS NEDERLANDS SVENSKA SVENSKA DANSK DANSK * When using control port pin 23 FADER (INVERT), pin 10 FADER (NORMAL) must be connected to pin 13 (FG COMMON) of the port. 19