Marantz SR4003 SR4003 User Manual - Englis - Page 11

NAMES AND FUNCTIONS BASIC CONNECTIONS BASIC OPERATION ADVANCED CONNECTIONS ENGLISH REAR PANEL qw er t y u VIDEO FM (75Ω) GND AM ANTENNA L SL C L S-VIDEO TV SBL R R SR SW SBR (AUX 2) 7.1CH INPUT TV INPUT 1 INPUT DVD VCR IN VCR OUT DSS MONITOR OUT 2 Y CB/PB CR/PR Y DVD IN OUT VCR DSS AUDIO IN OUT TAPE IN OUT CD/CDR CB/PB INPUT 3 COMPONENT VIDEO MONITOR OUT CR/PR IN 3 4 INPUT 1 1 2 DIGITAL IN OPT OUT FLASHER DIGITAL OUT REMOTE CONT. IN INPUT 2 INPUT 3 OUTPUT L SL C SBL R L R L R L AC OUTLETS 120V 60Hz AC IN R SR SW SBR PRE OUT FRONT SURROUND BACK SURROUND S. SPEAKER B SPEAKER SYSTEMS : 6-8 OHMS CENTER SWITCHED 1.25A 150W MODEL NO. SR4003 !5 !4 !3 !2 !1 !0 o i q FM antenna terminal (75 ohms) Connect an external FM antenna with a coaxial cable, or a cable network FM source. AM antenna and ground terminals Connect the supplied AM loop antenna. Use the terminals marked "AM" and "GND". The supplied AM loop antenna will provide good AM reception in most areas. Position the loop antenna until you hear the best reception. w 7.1 CHANNEL or AUX2 INPUT By connecting a DVD Audio player, Super Audio CD multichannel player, or other components that has a multichannel port, you can playback the audio with 5.1 channel or 7.1 channel outputs. e VIDEO IN/OUT (TV, DVD, VCR, DSS) These are the video inputs and outputs. There are 4 video inputs and 2 video outputs and each one includes both composite video and S-video configurations. Connect VCRs, DVD players, and other video components to the video inputs. The 2 video output channels can be used to be connected to video tape recorders for making recordings. r MONITOR OUT This is a monitor output and each one includes both composite video and S-video configurations. When connecting two video monitors or televisions, be aware that the OSD interface can be used with both MONITOR OUT connections. t COMPONENT VIDEO INPUT/ OUTPUT If your DVD player or other device has component video connectors, be sure to connect them to these component video connectors on the unit. This unit has two component video input connectors to obtain the color information (Y, CB, CR) directly from the recorded DVD signal or other video component and one component video output connector to output it directly into the matrix decoder of the display device. By sending the pure DVD component video signal directly, the DVD signal forgoes the extra processing that normally would degrade the image. The result is vastly increased image quality, with incredibly life like colors and crisp detail. When the video convert function is enabled, video and S-video images can be output to the COMPONENT MOINTOR OUT jack. y REMOTE CONT. IN/OUT terminals Connect to a Marantz component equipped with remote control (RC-5) terminals. u HDMI INPUT/OUTPUT This unit has 3 HDMI inputs and 1 HDMI output. The input function can be selected from the OSD menu system. (See page 21) i AC INLET Plug the supplied power cable into this AC INLET and then into the power outlet on the wall. This unit can be powered by 120V AC only. o Flasher IN This terminal controls the unit from each zone. Connect the control signal from a Keypad, etc. !0 AC OUTLETS Connect the AC power cable of component such as a DVD or CD player to this outlet. This outlet provides power only when this unit is turned on. Caution: • In order to avoid potential turn-off thumps, anything plugged into this outlet should be powered up before this unit is turned on. • The capacity of this AC outlet is 150W. Do not connect devices that consume electricity more than the capacity of this outlet. If the total power consumption of the connected devices exceeds the capacity, the protection circuit shuts down the power supply. !1 DIGITAL INPUT These are the digital audio inputs and outputs. This unit has 2 coaxial digital inputs and 2 optical digital inputs. The inputs accept digital audio signals from a CD, DVD, or other digital source component. This unit has 1 optical digital output. The digital output can be connected to MD recorders, CD recorders, or other similar components. !2 Speaker outputs terminals Seven terminals are provided for the front left, front right, front center, surround left, surround right, surround back left and surround back right speakers. Note: You can use surround back speaker terminals as S (Surround) SPEAKER B terminals, when you use no surround back speaker. !3 AUDIO IN/OUT (CD, TAPE, CD-R, TV, DVD, VCR, DSS) These are the analog audio inputs and outputs. There are 6 audio inputs (4 of which are linked to video inputs) and 3 audio outputs (1 of which are linked to video outputs). The audio jacks are nominally labeled for cassette tape decks, compact disc players, DVD players and etc.... The audio inputs and outputs require RCA-type connectors. !4 Subwoofer Output Connect this jack to the line level input of a powered subwoofer. If an external subwoofer amplifier is used, connect this jack to the subwoofer amplifier input. If you are using two subwoofers, either powered or with a 2 channel subwoofer amplifier, connect a "Y" connector to the subwoofer output jack and run one cable from it to each subwoofer amplifier. !5 Preamp Outputs (L, R, SL, SR, SBL, SBR, C) Jacks for L(front left), R (front right), C (Center), SL (surround left), SR (surround right), SBL (surround back left) and SBR (surround back right). Use these jacks for connection to external power amplifiers. SETUP ADVANCED OPERATION TROUBLESHOOTING OTHERS 8