Marantz SR5001 Marantz AV Receiver IR Remote Code List - Page 23

ENGLISH ADVANCED CONNECTING CONNECTING THE REMOTE CONTROL JACKS RL RL RL RL RL RL CENTER L R FRONT SURR. SURR. SUB BACK WOOFER DVD Audio player or Super Audio CD Multi channel player VIDEO FM (75Ω) GND AM S-VIDEO ANTENNA TV L SL C SBL L DVD VCR IN R R SR SW (AUX2) 7.1CH INPUT SBR MULTI. OUT TV RS-232C SPEAKER C OFF ON DVD IN VC L SL C SBL R L FRONT B R SR SW SBR FRONT A OR B,CENTER, PRE OUT SURR,SURR BACK:MINIM FRONT A AND B:MINIMU LR LR LR RL RL RL CENTER L R FRONT SURR. SURR. SUB BACK WOOFER Power Amplifer UNSWITCHED 1.25A 150W Subwoofer SWITCHED 1.25A 150W AC OUTLETS 120V 60Hz Front Left Center Front Right Surround Left Surround Right Surround Back Left Surround Back Right CONNECTING MULTI CHANNEL AUDIO SOURCE The 7.1CH INPUT jacks are for multichannel audio source such as a Super Audio CD multichannel player, DVD audio player or external decoder. If you use these jacks, switch on the 7.1CH INPUT and set the 7.1CH INPUT level by using the SETUP MAIN MENU. See page 29. CONNECTING AN EXTERNAL POWER AMPLIFIER The PREOUT jacks are for connecting external power amplifiers. Be sure to connect each speaker to the corresponding external power amplifier. INPUT 1 INPUT 3 COMPONENT VIDEO MONITOR DVD INPUT VCR IN VCR OUT DSS/VCR2 MONITOR OUT 2 Y CB/PB CR/PR OUT 2 Y CB/PB CR/PR Y CB/PB CR/PR INPUT 1 2 3 4 COAX IN DVD IN OUT IN VCR1 DSS/VCR2 IN OUT CD TAPE AUDIO IN OUT CDR/MD 1 2 3 OPT OUT DIGITAL IN DIGITAL OUT RC-5 FLASHER DC IN TRIGER L R L R L R L T B B.CENTER. FRONT A SURROUND BACK SPEAKER C/ SURROUND CENTER SPEAKER AC OUTLET 230V 50/60Hz 1 BACK : 6-8 OHMS MULTI SPEAKER SYSTEMS SWITCHED : 8 OHMS 0.65A 150W RC OUT OPTION REMOTE CONTROL IN OUT CD recorder EXTERNAL INTERNAL REMOTE CONTROL IN OUT MD deck EXTERNAL INTERNAL REMOTE CONTROL IN OUT CD player EXTERNAL INTERNAL q You can control other Marantz products through this unit with the remote control by connecting the REMOTE CONTROL terminals on each unit. The signal transmitted from the remote control is received by the remote sensor on this unit. Then the signal is sent to the connected device through this terminal. Therefore you need to aim the remote signal only to the unit. Also, if a Marantz power amplifier (some models excluded) is connected to one of these terminals, the power amplifier's, power switch is synchronized with this unit's power switch. Set the REMOTE CONTROL SWITCH on the units, other than the main unit to EXT.(EXTERNAL) for this feature. w Whenever external infrared sensors or similar devices are connected to RC-5 IN of the SR4001/ SR5001, be sure to always disable operation of the infrared sensor on the main unit by using the following procedure. 1. Hold down the 7.1CH INPUT (SR4001) / MULTI (SR5001) button and MENU button on the front panel at the same time for five seconds. 2. The setting "IR=ENABLE" is shown on the FL DISPLAY. 3. Press the 1 or 2 cursor button to change this to "IR=DISABLE". 4. Press the ENTER button. Once this setting is made, the infrared sensor on the main unit is disabled. Note: Be sure to set to "IR=ENABLE" when external infrared sensors or similar devices are not connected. Otherwise, the main unit will be unable to receive remote control commands. 5. To restore the original setting, perform steps 1 to 4 to set to "IR=ENABLE". 20