Marantz SR8500 SR7500 User Manual - Page 16

Connecting Audio Components

Get Marantz SR8500 PDF manuals and user guides View all Marantz SR8500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

LR ENGLISH Caution: • Be sure to use speakers with the specified impedance as shown on the rear panel of this unit. • To prevent damage to circuitry, do not let the bare speaker wires touch each other and do not let them touch any metal part of this unit. • Do not touch the speaker terminals when the power is on. It may cause you to receive an electric shocks. • Do not connect more than one speaker cable to one speaker terminal. Doing so may damage this unit. Note: • Be sure to connect the positive and negative cables for the speaker properly. If they are miss-connected, the signal phase will be reversed and the signal quality will be corrupted. CONNECTING A SUBWOOFER Use the PRE OUT SUBWOOFER jack to connect a powered subwoofer (power amplifier built in ). If your subwoofer is a passive type (power amplifier is not built in), connect a monaural power amplifier to the PRE OUT SUBWOOFER jack and connect the subwoofer to the amplifier. CONNECTING AUDIO COMPONENTS CD RECORDER / MD DECK DIGITAL OUT OUTPUT L R OUT IN DIGITAL DIGITAL L L INPUT OUTPUT LR R R CD PLAYER OUT IN L L R R LR LR TAPE DECK LR RL LR LR LR ANALOG AUDIO ANTENNA FM (75½) GND AM VIDEO DVD DSS/VCR2 COMPONENT VIDEO MONITOR OUT Y CB/PB CR/PR Y CB/PB CR/PR Y CB/PB CR/PR TV VCR1 S-VIDEO TV DVD VCR1 IN OUT DSS/VCR2 IN OUT MONITOR OUT MULTI OUT INPUT-1 TV DVD VCR1 IN OUT INPUT-2 DSS/VCR2 IN OUT OUTPUT MONITOR OUT DVI-D DIGITAL IN 4 5 6 DIGITAL OUT COAX. RS-232C RC-5 MULTI RC IN FLASHER IN L 1 2 1 2 3 TV L DVD VCR1 OPT. DSS/VCR2 CD TAPE OUT 1 DC OUT 2 R CDR/MD MULTI L SL SR SL R IN OUT IN OUT IN OUT AUDIO IN OUT OUT R (AUX2) SR SBL C PRE OUT SBR SBL SW C 7.1CH IN SBR SW DIGITAL AUDIO (COAXIAL) OFF SPEAKER C ON DIGITAL AUDIO R L (OPTICAL) SURROUND BACK/ MULTI SPEAKER/ SPEAKER C AC IN AC OUTLET 230V 50/60HZ SWITCHED 100W MAX. R L R L R L FRONT A FRONT B CENTER SPEAKER SYSTEMS FRONT A OR B, CENTER, SURR, SURR BACK : 6 - 8 OHMS FRONT A + B :8 OHMS SURROUND RL RL The output audio signal from the TAPE OUT jack and the CD-R/MD OUT jack is the same signal which is currently selected. Caution: • Do not connect this unit and other components to mains power until all connections between components have been completed. Notes: • Insert all plugs and connectors securely. Incomplete connections may make noise. • Be sure to connect the left and right channels properly. Red connectors are for the R (right) channel, and white connectors are for the L (left) channel. • Be sure to connect input and output properly. • Refer to the instructions for each component that is connected to this unit. • Do not bind audio/video connection cables with power cords and speaker cables this will result in generating a hum or other noise. CONNECTING DIGITAL AUDIO COMPONENTS • There are 6 digital inputs, 3 coaxial jacks and 3 optical jacks, on the rear panel. You can use these jacks to input PCM, Dolby Digital and DTS bitstream signals from a CD, DVD, or other digital source components. • There is one digital output coaxial jack and one optical output jack on the rear panel. These jacks can be connected to a CD recorder-, or a MD deck inputs, respectively. • Refer to the instructions for each component. To setup the digital audio format of DVD player, or other digital source's connected to digital input jacks. • Use fiber optical cables (optical) for DIG-1,2,3 input jacks. Use 75 ohms coaxial cables (for digital audio or video) for DIG-4, 5, 6 input jacks. • You can designate the input for each digital input/output jacks according to your component. See page 19. Notes: • There is no Dolby Digital RF input jack. Please use an external RF demodulator Dolby Digital decoder when connecting the Dolby Digital RF output jack of the video disc player to the digital input jack. • The digital signal jacks on this unit conform to the EIA standard. If you use a cable that does not conform to this standard, this unit may not function properly. • Each type of audio jack works independently. Signals input through the digital and analog jacks are output through the corresponding digital and analog jacks, respectively. 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
13
ENGLISH
Caution:
•
Be sure to use speakers with the specified impedance
as shown on the rear panel of this unit.
•
To prevent damage to circuitry, do not let the bare
speaker wires touch
each other and do
not let them touch
any metal part of
this unit.
•
Do not touch the
speaker terminals
when the power is
on. It may cause
you to receive an electric shocks.
•
Do not connect more than one speaker cable to
one speaker terminal. Doing so may damage this
unit.
Note:
•
Be sure to connect the positive and negative cables
for the speaker properly. If they are miss-connected,
the signal phase will be reversed and the signal
quality will be corrupted.
CONNECTING A SUBWOOFER
Use the PRE OUT SUBWOOFER jack to connect
a powered subwoofer (power amplifier built in ).
If your subwoofer is a passive type (power amplifier
is not built in), connect a monaural power amplifier
to the PRE OUT SUBWOOFER jack and connect
the subwoofer to the amplifier.
CONNECTING AUDIO COMPONENTS
OUT
IN
L
R
L
R
OUT
L
R
L
R
L
R
L
R
R
L
R
L
R
L
OUT
IN
L
R
L
R
DIGITAL
INPUT
DIGITAL
OUTPUT
DIGITAL
OUTPUT
R
L
R
L
R
L
R
L
L
R
The output audio signal from the TAPE OUT jack
and the CD-R/MD OUT jack is the same signal which
is currently selected.
Caution:
•
Do not connect this unit and other components to
mains power until all connections between
components have been completed.
Notes:
•
Insert all plugs and connectors securely.
Incomplete connections may make noise.
•
Be sure to connect the left and right channels
properly.
Red connectors are for the R (right) channel, and
white connectors are for the L (left) channel.
•
Be sure to connect input and output properly.
•
Refer to the instructions for each component that
is connected to this unit.
•
Do not bind audio/video connection cables with
power cords and speaker cables this will result in
generating a hum or other noise.
CONNECTING DIGITAL AUDIO COMPONENTS
•
There are 6 digital inputs, 3 coaxial jacks and 3
optical jacks, on the rear panel. You can use
these jacks to input PCM, Dolby Digital and DTS
bitstream signals from a CD, DVD, or other
digital source components.
•
There is one digital output coaxial jack and one
optical output jack on the rear panel. These
jacks can be connected to a CD recorder-, or a
MD deck inputs, respectively.
•
Refer to the instructions for each component. To
setup the digital audio format of DVD player, or
other digital source
’
s connected to digital input
jacks.
•
Use fiber optical cables (optical) for DIG-1,2,3
input jacks.
Use 75 ohms coaxial cables (for
digital audio or video) for DIG-4, 5, 6 input jacks.
•
You can designate the input for each digital
input/output jacks according to your component.
See page 19.
CD RECORDER / MD DECK
CD PLAYER
TAPE DECK
ANALOG AUDIO
DIGITAL AUDIO
(COAXIAL)
DIGITAL AUDIO
(OPTICAL)
Notes:
•
There is no Dolby Digital RF input jack. Please
use an external RF demodulator Dolby Digital
decoder when connecting the Dolby Digital RF
output jack of the video disc player to the digital
input jack.
•
The digital signal jacks on this unit conform to the
EIA standard.
If you use a cable that does not
conform to this standard, this unit may not
function properly.
•
Each type of audio jack works independently.
Signals input through the digital and analog jacks
are output through the corresponding digital and
analog jacks, respectively.