Marantz SR8500 SR7500 User Manual - Page 35

ENGLISH BASIC OPERATION (TUNER) To operate the unit from the remote control, press the TUNER button on the remote control so that the tuner mode is engaged. LISTENING TO THE TUNER Frequency scan step for AM is selectable. Default setup is 10 kHz step, if your country's standard is 9 kHz step, Press TUNER button on the remote more than 6 seconds. Scan step will change. Note: • Preset memory for the tuner will clear by changing this setup. AUTO TUNING 2. 1. DISP MULTI AUTO TUNED SLEEP AUTO SURR DIRECT ST SPKR A B V-OFF PEAK ATT DISC 6.1 MT X 6.1 NIGHT EQ ANALOG DIGITAL AAC PCM SURROUND DIGITAL LCR LFE SL S SR DOWN SOURCE USE PAGE 2 M 3. D1 D2 3. D3 D4 2. D5 ENTER DIGITAL S-VID TUNER CD CD-R MD TAPE AUX1 AUX2 AMP 1. LIGHT 1 2 RC8500SR Learning Remote Controller (Using the remote control unit) 1. To select tuner and desired band (FM or AM), press the TUNER button twice within two seconds on the remote. 2. Press the > button until PAGE2 is displayed. 3. Press and hold the SCAN+ (D1) or SCAN- (D2) button for 1 second or more. 4. Automatic searching begins then stops when a station is tuned in. If tuning does not stop at the desired station, use to the "Manual tuning" operation. MANUAL TUNING 2. 1. DISP MULTI AUTO TUNED SLEEP AUTO SURR DIRECT ST SPKR A B V-OFF PEAK ATT DISC 6.1 MT X 6.1 NIGHT EQ ANALOG DIGITAL AAC PCM SURROUND DIGITAL LCR LFE SL S SR DOWN SOURCE USE PAGE 2 M 3. D1 D2 3. D3 D4 2. D5 ENTER DIGITAL S-VID TUNER CD CD-R MD TAPE AUX1 AUX2 AMP 1. LIGHT 1 2 RC8500SR Learning Remote Controller (Using the SR7500) 1. To select tuner and desired band (FM or AM), press the BAND button on the front panel 2. Press the or cursor buttons on the front panel to select the desired station. DIRECT FREQUENCY CALL PREV MENU TEST 1 7.1CH 4 DISP 7 CLEAR LIP.SYNC GUIDE CH.SEL 2 ATT 5 OSD 8 THX 0 MUTE EXIT SURR 3 SPK-AB 6 SLEEP 9 MEMO 2. 3. TUNER CD CD-R MD TAPE 1 AUX1 AUX2 LIGHT RC8500SR Learning Remote Controller AMP 2 1. 1. To select tuner and desired band (FM or AM), press the TUNER button twice within two seconds on the remote. 2. Press the GUIDE on the remote, display will show "FREQ - - - -". 3. Input your desired station's frequency with the ten numbered keypad on the remote. 4. The desired station will automatically be tuned. (FM) TUNING MODE (AUTO STEREO OR MONO) V-OFF PEAK ATT 6.1 NIGHT EQ ANALOG DIGITAL AAC PCM SURM ROOUNDDE DIGITAL LCR LFE SL S SR VOLUME DOWN UP USE PAGE 1 M D1 D2 D3 D4 D5 R DIGITAL AUX 1 INPUT S-VIDEO VIDEO L AUDIO R CH VOL TV DVD VCR DSS TUNER CD CD-R MD TAPE AUX1 AUX2 AMP When in the auto stereo mode, AUTO indicator will be illuminated on the display. The "ST" indicator is illuminsted when a stereo broadcast is tuned in. At open frequencies, the noise is muted and the "TUNED" and "ST" indicators are not illuminated. If the signal is weak, it may be difficult to tune into the station in stereo. In such a case, press the MODE button on the front panel.Or press the TUNER button and press the > button until PAGE1 is displayed. Press the T-MODE (D4) button. "AUTO" indicator is not illuminated, if FM stereo broadcasts are received in monaural and the "ST" indicator is not illuminated. To return to auto stereo mode, press the MODE button or press T-MODE button on the remote again. AUTO indicator is illuminated the display. (Using the SR7500) 1. To select tuner and desired band (FM or AM), press the BAND button on the front panel. 2. Press the or cursor buttons on the front panel for more than 1 second to start the auto tuning function. 3. Automatic searching begins then stops when a station is tuned in. (Using the remote control unit) 1. To select tuner and desired band (FM or AM), press the TUNER button twice within two seconds on the remote. 2. Press the > button until PAGE2 is displayed 3. Press the SCAN+ (D1) or SCAN- (D2) button to tune in the deseired station. 32