Marantz SR8500 SR7500 User Manual - Page 25

ENGLISH Notes: • The measured speaker distance may differ from the actual distance from speakers. Nevertheless, the measured value is suitable for the speakers. • To make changes to individual speakers, select 2. SPEAKER SETUP on the SETUP MAIN MENU, then select MANUAL for 2-1 SPEAKER SETUP. • The included microphone is designed specifically for this receiver. Other microphones do not guarantee suitable measurement results. Use the included microphone to conduct measurements. • During measurement, press the ENTER or EXIT button to cancel measurement. • In some rooms, an error may occur during auto speaker setup or it may not be possible to set Speaker distance correctly because of room acoustics. In such case, set the speaker distance by MANUAL setup. Error Indications During Measurement If trouble occurs during measurement, an error message is displayed on the monitor screen and FL display. Those errors and their remedies are described below. The message appearing on the FL display is given in ( ). MIC SETUP ERROR (MIC SET ERROR) The microphone (MC-10) is not properly connected. → Check the microphone connection. AMBI NOISE ERROR (AMBI NOISE ER) Measurement cannot be done correctly because of excessive ambient noise. → Either temporarily turn off power to noisy devices such as air conditioning or move them out of the room. → Retry measurement when the room is quiet. SPEAKER SET ERROR (SPK SET ERROR) The speakers are not properly connected. → Recheck speaker layout and connections. 22 3 PREFERENCE 3 PREFERENCE S T ANDB Y MOD E T V - AUTO OSD I NFO V I DEO CONVERT L FE LEVEL : N NORMAL : D I SABLE : ENABLE : ENABLE : 0 dB MA I N EX I T 1. Select "PREFERENCE" in the SETUP MAIN MENU with the or cursor buttons, and press the ENTER button. 2. To select a desired content, press the or cursor buttons. STANDBY MODE: When this function is set to "ECONOMY", you can reduce the power consumption when the unit is in the standby mode. Note: • TV-AUTO and RS-232C are disabled in the "ECONOMY" setting. TV AUTO: Select the TV AUTO ON/OFF function to enable or disable with the or cursor buttons. (refer to page 29) OSD Info: Select the OSD information function to enable or disable with the or cursor buttons. If you select "ENABLE", the SR7500 will display the status of the feature (Volume up/down, input select, etc..) on the TV monitor. But if you do not desire this information, select "DISABLE ". VIDEO CONVERT: Select the VIDEO CONVERT function to enable or disable with the or cursor buttons. (Video cable connection: Refer to page 24) LFE LEVEL: Select the output level of the LFE signal included in the Dolby Digital signal or the DTS signal. Select 0 dB, -10 dB or OFF with the or cursor buttons. After you complete this portion of the set up, move the cursor to "MAIN" with the or cursor buttons and press the ENTER button. 4 PL II (PRO LOGIC II) MUSIC PARAMETER Pro Logic II-Music mode creates a rich and enveloping surround ambience from stereo sources such as CDs. In this mode, SR7500 includes three controls to fine-tune the soundfield as follows. 4 P L II MU S I C P ARAME T E R PARAME T ER : DEFAUL T P A NOR AMA : OFF D I MENS I ON :4 CENTER WI DTH : 0 MA I N EX I T Select "PL II MUSIC" in the SETUP MAIN MENU with the or cursor buttons, and press the ENTER button. PARAMETER: Select "DEFAULT" or "CUSTOM" with the or cursor buttons. If you select "CUSTOM", you can adjust three parameters as listed below. PANORAMA: Select the Panorama mode On or Off with the or cursor buttons. Panorama wraps the sound of the front left and right speakers around you, for an exciting perspective. DIMENSION: Set the Dimension level between 0 and 6 level in 1 level intervals with the or cursor buttons. Adjust the soundfield either towards the front or towards the rear. This can be useful to help achieve a more suitable balance from all the speakers with certain recordings. CENTER WIDTH: Set the Center width level between 0 and 7 in 1 level intervals with the or cursor buttons. Center Width allows you to gradually spread the center channel sound into the front left and right speakers. At its widest setting, all the sound from the center is mixed into the left and right. This control may help achieve a more spacious sound or a better blend for the front image. If "NONE" was selected for the Center speaker setting, in the Speaker size set up menu, then this setting will not appear. After you complete this portion of the set up, move cursor to "MAIN" with the or cursor buttons and press the ENTER button. 5 CS II (CIRCLE SURROUND II) PARAMETER 5 C S II P ARAME T E R T RUBA S S SRS D I A LOG :0 :0 MA I N EX I T 1. Select "CS II" in the SETUP MAIN MENU with the or cursor buttons, and press the ENTER button. 2. To Select desired contents as below, press the or cursor buttons. TRUBASS: Set the TRUBASS level between 0 and 6 level in 1 level interval with the or cursor buttons. TRUBASS produced by the speakers are an octave below the actual physical capabilities of the speakers adding exciting, deeper bass effects. SRS DIALOG: Set the SRS DIALOG level between 0 and 6 in 1 level intervals with the or cursor buttons. This can be popped out of the surround audio effects, allowing the listener to easily discern what the actors say. If "NONE" was selected for the Center speaker setting, in the Speaker size set up menu, then this setting will not appear. After you complete this portion of the set up, move cursor to "MAIN" with the or cursor buttons and press the ENTER button.