Marantz VP-12S4 User Manual - Page 28
Display, OSD/Blanking - projector remote control
View all Marantz VP-12S4 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 28 highlights
Display OSD/Blanking ENGLISH Standard 1 Fine Menu 1 Fine Menu 2 Input Signal RGB/HD Adjust Display OSD/Blanking Config. Keystone Scale Width Position H Position V Installation 0 0 0 0 0 Front Item Keystone (Electronic vertical keystone correction) Scale Width Position H Position V Installation Adjustments -50 0 50 ( ) ( )( ) -100 (Min) 0 (Max) -100 (Min) 0 (Max) -50 0 50 (Left) (Default) (Right) -50 0 50 (Down) (Default) (Up) Front, Rear, F+Ceiling, R+Ceiling - Keystone Adjust trapezoid image to rectangle image. - Scale Reduces the image without changing the aspect ratio. The image can be reduced to about 70% the original size. - Width Reduces the image width without changing the image height. The width can be reduced to about 75% the original size. - Position H, V Adjust the position of the input signal. H adjusts the horizontal position of the input signal. V adjusts the vertical position of the input signal. However, when Scale and Width are set to their default settings, the picture position cannot be adjusted. - Instllation Sets the installation mode of the projector. Front: Select to set the projector on a tabletop and project from in front of the screen. Rear: Select to set the projector on a tabletop and project from behind the screen. F + Ceiling: Select to mount the projector on the ceiling and project from in front of the screen. R + Ceiling: Select to mount the projector on the ceiling and project from behind the screen. 22 Standard 1 Picture Adjust Fine Menu 1 Fine Menu 2 Input Signal RGB/HD Adjust Display OSD/Blanking Config. Menu Position Top-L Language English Status Info. Enable Power-OFF Confirm. Enable Blanking Memory Memory 1 Blanking Top 0 Blanking Bottom 0 Blanking Left 0 Blanking Right 0 Item Menu Position Language Status Info. Power-OFF Confirm. Blanking Memory Blanking Top Blanking Bottom Blanking Left Blanking Right Adjustments Top-L, Top, Top-R, Center-L, Center, Center-R, Bottom-L, Bottom, Bottom-R English, Deutsch, Français, Español, Português, Italiano Enable, Disable Enable, Disable Off, Memory 1, Memory 2, Memory 3 0 100 0 100 0 100 0 100 - Menu Position OSD position is selected from 9 positions. - Status Info. Enable: Displays the current status of the projector for a set amount of time in the upper right-hand corner of the screen at startup and whenever the Input Source, Picture Mode, Aspect ratio or other setting is changed. Disable: Does not display Status Info. - Power-OFF Confirm. Disable: Directly puts the projector on standby without displaying the confirmation message when power is shut off from the button on the remote controller or the /I button on the projector. Enable: Displays a confirmation message asking whether to shut the power off or continue use when power is shut off from the button on the remote controller or the /I button on the projector. To shut off the power immediately, select "Yes" and press the ENTER button. To not shut off the power, select "No" and press the ENTER button. - Blanking Memory Sets the blanking mode with which part of the screen can be hidden in black bands. To use this mode or change the setting, select from Memory 1 to 3. Off: Turns the blanking mode off. No masking occurs. Memory 1-3: Memorize the blanking width of the top, bottom, left and right masks set with the below features. Up to three settings can be memorized. - Blanking Top, Bottom, Left and Right Set the blanking width of the top, bottom, left and right masks, which are then memorized in Memory 1 - 3 of Blanking Memory. Each can be set from 0 (no mask) to a maximum 100.