McAfee IIP-S03K-NA-100I Product Guide - Page 23

Removing a power supply

Get McAfee IIP-S03K-NA-100I - IntruShield 3000 Sensor Appliance PDF manuals and user guides
UPC - 731944579931
View all McAfee IIP-S03K-NA-100I manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

McAfee® IntruShield® IPS 4.1 IntruShield Sensor 3000 Product Guide Setting up the I-3000 sensor prior to configuration Installing the I-3000 redundant power supply 3 Place the power supply in the slot with the cable outlet facing front and on the left side of the faceplate. Figure 4: Installing a power supply 4 Slide in the power supply until it makes contact with the backplane, then push firmly to mate the connectors solidly with the backplane. 5 Secure the power supply's front panel to the sensor chassis using the mounting screw on the left of the power supply's front panel. Note: For true redundant operation with the optional redundant power supply, McAfee recommends that you plug each supply into a different power circuit. For optimal protection, use uninterrupted power sources. Removing a power supply ► To remove a power supply from the I-3000 (Optional-the power supplies are hot-swappable): 1 Unplug the power cable from its power source and remove the power cable from the power supply. 2 Put on an antistatic wrist or ankle strap. Attach the strap to a bare metal surface of the chassis. 3 Unscrew the screws connecting the mounting bracket and remove the bracket from the front the power supply. 4 Squeeze the handle of the power supply and pull it out. 5 Use faceplate panels to protect unused slots from dust and reduce electromagnetic radiation. 6 Replace the mounting bracket. Warning 1: To remove all power from the I-3000 sensor, unplug all power cords. Warning 2: To avoid data interruption, do not power off both power supplies on an in-line sensor, or the sensor shuts down and all data traffic stops. Power off only the power supply you are replacing. 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
McAfee® IntruShield® IPS 4.1
Setting up the I-3000 sensor prior to configuration
IntruShield Sensor 3000 Product Guide
Installing the I-3000 redundant power supply
3
Place the power supply in the slot with the cable outlet facing front and on the
left side of the faceplate.
Figure 4: Installing a power supply
4
Slide in the power supply until it makes contact with the backplane, then push
firmly to mate the connectors solidly with the backplane.
5
Secure the power supply’s front panel to the sensor chassis using the mounting
screw on the left of the power supply’s front panel.
Note:
For true redundant operation with the optional redundant power supply,
McAfee recommends that you plug each supply into a different power circuit. For
optimal protection, use uninterrupted power sources.
Removing a power supply
►
To remove a power supply from the I-3000 (Optional—the power
supplies are hot-swappable):
1
Unplug the power cable from its power source and remove the power cable
from the power supply.
2
Put on an antistatic wrist or ankle strap. Attach the strap to a bare metal surface
of the chassis.
3
Unscrew the screws connecting the mounting bracket and remove the bracket
from the front the power supply.
4
Squeeze the handle of the power supply and pull it out.
5
Use faceplate panels to protect unused slots from dust and reduce
electromagnetic radiation.
6
Replace the mounting bracket.
Warning 1:
To remove all power from the I-3000 sensor, unplug all power cords.
Warning 2
: To avoid data interruption, do not power off both power supplies on an
in-line sensor, or the sensor shuts down and all data traffic stops. Power off only
the power supply you are replacing.
15