Miele CVA 4066 Operating and Installation manual - Page 54

Descaling, lukewarm, under-fill, descaling tablets, Add fresh water to tank, empty the drip tray

Get Miele CVA 4066 PDF manuals and user guides View all Miele CVA 4066 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 54 highlights

Descaling the appliance Descaling Maintenance q r HI J L n mC ^ Tap < or > until "Maintenance m" is highlighted, confirm with OK. ^ Select "Descale" and confirm with OK or, when the appliance is switched off, tap the OK button. ^ Select "Start", tap OK to begin the descaling process. The display prompts the user through the single steps of the descaling process. Follow the prompts. If the descaling is started while the machine is still hot, the appliance will cool down for 10 minutes before the descaling begins. The descaling process cannot be canceled once "OK" is selected. The process now needs to be completed. This is a safety feature to ensure the process will be completed. It is important for best results and the longevity of the machine. To dissolve the descaling tablets: ^ Remove the water tank and fill it up to the k mark with lukewarm water. (Do not under-fill the water tank, because this will cause the descaling cycle to end prematurely, before completion.) ^ Add 2 descaling tablets to the water and allow them to dissolve completely before closing the water tank and placing it back into the machine. During the descaling cycle, the descaling agent-water solution will run out of the hot water spout and the main dispenser. This will be followed by a pause to allow the solution to dissolve the internal mineral buildup, after which more descaling solution with be released from the spouts. This process will repeat itself until the cycle is finished. ^ When the display prompts you to Add fresh water to tank, rinse the tank thoroughly with clear water (all traces of descaling residue must be removed) and fill it with clean drinking water up to the k mark. During rinsing, water will run out of the dispensing spouts. Because the inside of the machine is also rinsed out, you must empty the drip tray in the final step. ^ When the display shows Prog. finished, tap OK. The appliance is now fully descaled and ready for use. If the appliance was set to the plumbed water supply before descaling, once the descaling process is complete it will return to that setting. 54

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
Descaling
Maintenance
q
r
H
I
J
L
n
m
C
^
Tap < or > until "Maintenance
m
" is
highlighted, confirm with OK.
^
Select "Descale" and confirm with OK
or, when the appliance is switched
off, tap the OK button.
^
Select "Start", tap OK to begin the
descaling process.
The display prompts the user through
the single steps of the descaling
process. Follow the prompts.
If the descaling is started while the
machine is still hot, the appliance
will cool down for 10 minutes before
the descaling begins.
The descaling process cannot be
canceled once "OK" is selected. The
process now needs to be
completed. This is a safety feature to
ensure the process will be
completed. It is important for best
results and the longevity of the
machine.
To dissolve the descaling tablets:
^
Remove the water tank and fill it up to
the
k
mark with
lukewarm
water.
(Do not
under-fill
the water tank,
because this will cause the descaling
cycle to end prematurely, before
completion.)
^
Add
2 descaling tablets
to the water
and allow them to dissolve
completely before closing the water
tank and placing it back into the
machine.
During the descaling cycle, the
descaling agent-water solution will run
out of the hot water spout and the main
dispenser. This will be followed by a
pause to allow the solution to dissolve
the internal mineral buildup, after which
more descaling solution with be
released from the spouts. This process
will repeat itself until the cycle is
finished.
^
When the display prompts you to
Add fresh water to tank,
rinse the
tank thoroughly with clear water (all
traces of descaling residue must be
removed) and fill it with clean
drinking water up to the k mark.
During rinsing, water will run out of the
dispensing spouts. Because the inside
of the machine is also rinsed out, you
must
empty the drip tray
in the final
step.
^
When the display shows
Prog.
finished
, tap OK.
The appliance is now fully descaled
and ready for use.
If the appliance was set to the
plumbed water supply before
descaling, once the descaling
process is complete it will return to
that setting.
Descaling the appliance
54