Miele CVA 4066 Operating and Installation manual - Page 62

Too much crema has formed and is above the coffee dispensers.

Get Miele CVA 4066 PDF manuals and user guides View all Miele CVA 4066 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 62 highlights

Frequently asked questions The message "Insert water tank until it engages" appears Possible fault Solution No water is dispensed. - The water tank is not inserted properly. Take it out and reinsert correctly. - The water tank was not filled correctly during the descaling process. Fill the water tank up to the correct mark. - If the message still appears contact Technical Service. The message "Check water inlet" appears Possible fault Solution The plumbed water intake is faulty. - Check for kinks in the water intake hose and open the water supply all the way. - Slide the water tank back in to the appliance. - If the fault is displayed again, call Technical Service. The gasket of the coffee dispenser connector is damaged and leaking. Possible fault Solution - The gasket is worn. - Change the gasket with a new one (supplied). - Check the door. Is the alignment - Adjust the door hinges. See "Installation - off from damage to the gasket? Adjusting the door hinges". Too much crema has formed and is above the coffee dispensers. Possible fault Solution Some coffee types produce too much crema when the coffee / espresso temperature is set to the maximum and the amount of ground coffee is too much. Lower the temperature and amount of coffee. 62

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
The message "Insert water tank until it engages" appears
Possible fault
Solution
No water is dispensed.
– The water tank is not inserted properly.
Take it out and reinsert correctly.
– The water tank was not filled correctly
during the descaling process. Fill the
water tank up to the correct mark.
– If the message still appears contact
Technical Service.
The message "Check water inlet" appears
Possible fault
Solution
The plumbed water intake is faulty.
– Check for kinks in the water intake hose
and open the water supply all the way.
– Slide the water tank back in to the
appliance.
– If the fault is displayed again, call
Technical Service.
The gasket of the coffee dispenser connector is damaged and leaking.
Possible fault
Solution
– The gasket is worn.
– Check the door. Is the alignment
off from damage to the gasket?
– Change the gasket with a new one
(supplied).
– Adjust the door hinges. See "Installation -
Adjusting the door hinges".
Too much crema has formed and is above the coffee dispensers.
Possible fault
Solution
Some coffee types produce too
much crema when the coffee /
espresso temperature is set to the
maximum and the amount of
ground coffee is too much.
Lower the temperature and amount of
coffee.
Frequently asked questions
62